## ### ## ## ## ####
## ### ## ## ## ## ## ## ####
## ## #### ## #### ## ##
_____ | __ \ | |__) | | _ / | | \ \ |_| \_\
###### ## ## ## ## ## ## ## ## ## ## ## ## ## ## ##
IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now. Visit Preferences to set your user name Summary of change: '''Big Six Turbo''' BMW called M30 engines as "Big Six" (M20, just like mine is "Little Six"). This page is about an M30B34 turbo engine, originally in a 745i from 1985. http://www.bmwpower.hu/gallery/albums/userpics/10152/normal_45i%20017.jpg It's not a weak car even it's stock form (3.5 Turbo, automatic, see pic), but this engine is now in a light chassis (e30): http://www.bmwpower.hu/gallery/albums/userpics/10152/normal_alkatr%E9szek%20022%7E0.jpg This page is about GenBoard-ing it! '''Original setup''' Car outlines: * Engine: M30B34 turbo, 3400cc, '''6 cyl inline''', 12 Valves, SOHC * Fuel injection: Bosch injectors (part no. 0 280 150 200) maybe 270-300 cc/min @3/3.5bars (different sources say different values). R=~3 Ohms. * Fuel pump: Stock * Stock 3 bar pressure regulator, with manifold pressure reference * '''Turbo''': stock KKK K27 * Idle control : stock. (similar to M20) * Intake: stock AFM, Small stock air-to-air intercooler * Factory throttle pos switch (3 state; idle, between and WOT) * VR crank-trigger: 60-2. ** M20 baby series engine uses exactly the same crank triggering, see MembersPage/GergelyLezsak/Trigger * Cam position sensor - coil at plug wire #6 * Coolant sensors - similar to M20 * '''Knock'''. Two factory installed knock sensors. * More sensors: O2 sensor: narrowband , IAT in AFM * orig '''ECU''': Bosch Motronic 0 046 430 136 0 Buylist at MembersPage/GergelyLezsak/BuyList ---- '''Project''' Electronically the M30 engine seems very similar to the M20 little brother (from the same era: motronic 1.3). Even their original ECU can be swapped, and the engine will start up! (mapping is not the same, so don't use this as a common practice) After i've received[http://quasar.dynaweb.hu/~lezsi/bmw/conversion/345i/parts-1.jpg first part of the order] I made a new harness, and ordered a new 3.3 GenBoard. I wanted to put it together on my M20 and then move the working system (with changed values of course) to the M30 engined car. ---- '''UPDATE''' 2005.12.28-29 Car is running with GenBoard :) We'have removed the whole factory harness. (Took a while to reproduce everything) Some experience: TPS wire's and IAC open/close wire's direction is always replaced :) Had some difficulties with digital outs; EC36pin15 (Which is P259/5) didn't do anything (with the fuelpump). Tried to move it to the next pin (P259/6), resulted the same. Finally chose a different chip: S259/5, EC18pin5. It's working. Couldn't imagine what could be wrong, at the test time fuelpump out was working. After we've got fuel I made it flooded. I don't know how but my previous calculations worthed nothing. I thought fuel_req at the 12ms range, but I needed to half that, and maybe we'll half it again. Idle (which is horrible now, but that's mainly pid-related) is around 1ms pw. Don't know why, these are ~300ccm injectors. Maybe too slow to close? Will try to lower pwm value of 30%, and PowerFlyback if necessary... Since we've got 25cm of snow the day the car started, couldn't tune it yet... Some pics: Dashboard: http://www.bmwpower.hu/gallery/albums/userpics/10152/thumbnails_analog%20muszerek%20010.jpg [http://www.bmwpower.hu/gallery/albums/userpics/10152/analog%20muszerek%20010.jpg in big] Nice work with the LCD mounting. The first day at the backyard (no snow at all): http://www.bmwpower.hu/gallery/albums/userpics/10152/thumbnails_udvar2.jpg [http://www.bmwpower.hu/gallery/albums/userpics/10152/udvar.jpg in big] ---- '''TODO''' * LCD with cable connection ** Done: not exactly with the specified resistors, but it's perfect. [http://quasar.dynaweb.hu/~lezsi/bmw/conversion/345i/lcd1.jpg pic1], [http://quasar.dynaweb.hu/~lezsi/bmw/conversion/345i/lcd2.jpg pic2] * Make whole harness ** Done * External MAP housing with connections ** Done * When GenBoard is ready, flash it with my IAC-tweaked firmware ** Done. We'll need to merge the few lines special IAC code to mainstream stable firmware. Do you have uptodate patch ? ** are you still using firmware with tps-accel enrichment accidentally disabled ? *** Yes, it's based on v14rc1. Now I'm eagerly waiting for coming of v30! (I'd test it even before release, if it's not ready yet!) * Mapping ** It's going to be a whole new story at MembersPage/GergelyLezsak/BigSixTurbo/Injectors * Setting IAC table/PID ** It's still an issue for this and my own car. Valve control seems allright, but can't get through the problems of very low RPMs (and sometimes stalling) at sudden throttle release. Details soon. * Boost control * Calibrate and test knock sensors. Checked dox but can't find out what knock1_frequency values actually means? ** the value directly from TPIC8101 datasheet (table), usually 0x29=41 but check for your freq. What is your freq? *** That's it! We don't know the freq yet but now I understand what I'll adjust, fine! :) * PowerFlyback? - Maybe, discuss at MembersPage/GergelyLezsak/BigSixTurbo/Injectors page ---- * Here is a similar car: MembersPage/MattiasSandgren/BmwSevenTwentyEight - Unfortunately the owner had to sell it for 1300 euro.. * Another similar car: MembersPage/MattiasSandgren/BmwFiveTwentyEight (Will be my daily driver //Mattias) and a [http://media.savarturbo.se/~mattias/vems/bmw_e23_728_turbo/pimpride_2005.avi movie clip] for motivation //Emil Larsson ---- Optional: Add document to category: Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.