#####  
 ##  ##  
 ##  ##  
  #####  
     ##  
 #####   

         
         
  #####  
 ##      
  ####   
     ##  
 #####   
         

         
|\     /|
| )   ( |
| |   | |
| |   | |
| |   | |
| (___) |
(_______)
         

______ 
|  ___|
| |_   
|  _|  
| |    
\_|    
       
       

   ##    
   ##    
  #####  
   ##    
   ##    
   ## ## 
    ###  
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
'''Knock Sensing''' BMW M102/M106 engines (similar to M30 + turbo) are factory equipped with two knock sensors. I'm trying to utilize them... - Unfortunately at the moment there's only support for one sensor at-a-time in firmware. I'd definitely like to utilize both of them in the future, but for now I need to stick with the second one which is located between cyl. 5-6. It is the well-known place of knock, more than the first sensor location, since cyl.6 is the hottest one. '''PLAN''' '''How to set up the characteristic knock frequency?''' Bore is 92mm, so r=46mm. '''1. Theory''' The expected knocking frequency is around 900/(pi*r) = 900/(3.14*46) = 6.2kHz '''2. Experience''' * record the knock-sensor output with notebook soundcard while knock sensor is connected (with a 50k series resistor) to the microphone input of a laptop. * adjust the ignition advance (usually upto 36 degrees in 4..5 steps) at idle until slight knock happens. * This is very hard without WideBand closed-loop EGO control, because the engine will want to stop before any knocking, and adjusting the fuel manually at the same time ignadv is adjusted is hard. * note that the MAP should be low, 25..40 kPa (max 55kPa), otherwise the engine is endangered. RPM also low (<1500 RPM). * play back the sound after the engine stopped. You'll be surprised how well the ping sound can be heard without the loud exhaust sounds. * just read the characteristic frequency from the FFT diagram. '''Config''' From TPIC8101 datasheet config value 39 stands for 6.37kHz, which is probably close to current typical knock freqency. * from global.h: uint8_t knock_conf; // knock, config. bit0 o FF means knock2... ?? o FD means knock1... (DEFAULT!) # Overall System Settings # Knock selection knock_conf = FF # enable knock-detection, will use Channel2! knock_sampling_window = e2 # ??? # Use knock sensing in this RPM range # FF for both means no knock sensing/control??? knock_minrpm = 05 # FF=No minimum RPM. 0x01=100rpm knock_maxrpm = FF # FF=No maximum RPM knock1_frequency = 27 # dec 39, 6.37kHz knock1_gain = 40 # ??? knock1_integrator = 14 # ??? knock2_frequency = 27 # dec 39, 6.37kHz knock2_gain = 40 # ??? knock2_integrator = 14 # ??? # Trigger level knock_threshold = 50 # ??? knock_noise_scale = 10 # ??? # Ignition effects # # Knock getting louder knock_max_retard = 50 # 20 degreees, 0x01=0.25 crank degrees. knock_default_retard = 10 # *0.25 crank degrees. knock_retard_step = 08 # 3.2 degrees knock_retard_delay = 10 # 0x01=15ms Retard delay. # Knock getting softer knock_advance_step = 02 # *0.25 crank degrees. knock_advance_delay = 10 # 0x01=15ms I'm '''totally lost''' with these config values. Couldn't find any usable info for those ??? values. Any idea?
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.