######  
  ##  ## 
  ##  ## 
  #####  
  ##     
 ####    

    #    
 ######  
   ##    
   ##    
   ##    
   ## #  
    ##   
         

         
         
 ######  
    ##   
   ##    
  ##     
 ######  
         

 _   _ 
| \ | |
|  \| |
| . ` |
| |\  |
\_| \_/
       
       

         
         
 ### ##  
 #  #  # 
 #  #  # 
 #  #  # 
 #  #  # 
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Hi, My projectcar is a 205 GTI with a 1.9 litre 8 valve engine. I turbocharged it some time ago and am now fully rebuilding/upgrading the engine to suit high boost. Have a look at my project webpage http://www.205turbo.nl specs in a nutshell: alloy 1905 CC wetliner engine 16 valve cyl head Mitsu td05 16g turbo --- Engine running problems. I have some problems with my engine. every once in a while it suddenly cuts fuel while cruising on the gighway. This lasts for about a few seconds and then it resumes again. What i can find in the logs is that: - engine status is 129. - AFR goes sky high - My tachometer still works (i.e. ignition should stil work) Anybody suggestions on what it might be? ---- '''Boost control''' Hi I've obtained an audi N75 valve and want to use it for boost control '''Q''' The primary question I have is: Can I use a extrafet/specfet for this or should I use a injector output for this? '''A''' Spec/extra fet can be used but since you are switching inductive loads fitting an flyback diode is required can be mounted either inside case or external across valve wires (diode pointing towards +vbat connection). ---- '''OLD / solved issues for reference by other users perhaps experiencing simmilar problems''' ---- '''Tachometer output''' I wired the tachometer to EC-18 pin 12 (SPECFET 0) and set the folowing parameters in megatune: Tachometer channel: SPECFET Tachometer channel: 0 Tachometer divider: 0 in the help it says: Most GenBoard outputs is only pulling the output low (0 volts) If your tachometer wants 12V or 5V signals, wire up a (say, 1kOhm to +12V or +5V) external pullup resistor. Configure Tachometer Divider if you want a lower frequency to your tachometer. Check out the latest MegaTune release package (mt-r27), it has 1.0.19 firmware which has the tach output working. > Ok, I have the mt-r27 formware working now, but still no tach output. The strange thing is: I would expect a led to work here. I wired a lef parallel with the pullup resitor but it didn't do anything. Is my logic flawed? Probably I so not really know how my tachomater works. It used to be connected to the coil (-). But I use a different coil now. (wasted spark) perhaps I'd just hook it up the old fashioned way with diodes? * Wired it up '''the oldfashioned way with diodes and works like a charm...''' ** so your tachometer needs high voltage to trigger. *** One option is the "inductive pullup" as described on [http://shop.vems.hu/catalog/product_info.php?products_id=102 inductor] *** but if the diode trick worked, no reason to change it. ---- '''Staging''' I added 4 injectors to my engine. So I now have 4 injectors aiming at the valves and 4 upstream. The secondary injectors are 305 cc and the primary injectors 240 cc. '''Configuration:''' I configured VEMS to do injector staging. * rate to calculated pulsewidth (inj_stage2_rate) to 200 * TPS position to 0% * MAP value to 130 kpa. Changed the firmware so the secondaries can be larger than the primaries. I changed the VE table so all values above 130 kpa are devided by 2. It works. Not quite how I had expected but after a bit of fiddling with the inj_stage2_rate it works. --- Megatune showed wrong voltage: * Only problem is the volt meter in Megatune. It gives 20 volt readings while battery voltage is 13 v. ** You probably missed to calibrate it, adjust battery calibration. Default batt_cal=0xBC (decimal 188) or so *** thanks for that! ---- Ignition problems. Fuel worked but no sprak. * Publish full config, saved by mcd command. * Try to compare your ignition related parameters with a working config, such as MembersPage/MarcellGal/EngineSwap . * As the last chance, start again from the working config, only change what is necessary. * check again if you missed something from GenBoard/UnderDevelopment/FirmwareChanges * Eg. make sure secondary_trigger=02 is used ? Thanks for the feedback! It turned out to be the secondary trigger indeed. ---- Took it for a drive this day. But the engine ran verry lean (afr 1:16) and it appeared all the tables are ampty somehow in megatune. I had this problem with a more recent firware before. Ans switched to a bit older one that seemed to work fine. But now the tables are empty again. Does anybode have any idea how this could be fixed? A: There was a ini update on the magatune page. http://www.vems.hu/wiki/index.php?page=MegaTune <<This package has bug in ini file causing settings lost when updating to ECU, here is [fixed ini file]>> ---- The engine didn't start -> no fuel injection. the pulse width megatune displays is 0 though the crancking pulsewidth is set. And the the req_fuel is set(and all tables are filled with the right values) A: somehow the decel fuel cut rpm was set to 0 rpm after a firmware update. I set is back to 2500 rpm and it started again.
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.