|\ /| | ) ( | | | | | | | | | | | | | | (___) | (_______)
_ | | | | | |___ |_____|
## ## ####### ####### ## # ## ## ##
___ / _ \ | | | | | |_| | \___/
## # ## ## # # ## ## # ### ## ## ## # #
IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now. Visit Preferences to set your user name Summary of change: Hi, My projectcar is a 205 GTI with a 1.9 litre 8 valve engine. I turbocharged it some time ago and am now fully rebuilding/upgrading the engine to suit high boost. Have a look at my project webpage http://www.205turbo.nl specs in a nutshell: alloy 1905 CC wetliner engine 16 valve cyl head Mitsu td05 16g turbo ---- Current issues / remarks I'm hitting 100% Duty cycle with my injectors. So now i want to add 4 extra in the runners. The hardware I have avaiable but I found little documentation on the staged injector setup in vems. what I found is: http://www.vems.hu/wiki/index.php?page=GenBoard%2FUnderDevelopment%2FStagedInjectors is this still the most recent information? i.e.: - are the bugs still in the system? - I need to reccompile the firmware for staged injector support? I want the secondary injectors to have the same p/w as the main injectors and want them only on boost ( perhaps > 130-150 kpa) the main (highz)injectors all have 1 driver and I was planning on using 2 drivers for the secondary injectors. (so one driver for two highz injectors) or would it be better to just connect 2 drivers to the main injectors and two to the secondary ones? any suggestions? ---- Tachometer out doesn't seem to work. I wired the tachometer to EC-18 pin 12 (SPECFET 0) and set the folowing parameters in megatune: Tachometer channel: SPECFET Tachometer channel: 0 Tachometer divider: 0 in the help it says: Most GenBoard outputs is only pulling the output low (0 volts) If your tachometer wants 12V or 5V signals, wire up a external pullup resistor use Tachometer Divider if you want a lower frequency to your tachometer. I haven't tried a pullup resistor yet. What kind of resistor should that be? The configuration values are added to config, but the tach-out implementation is not yet in stable firmware. >> Ok i'll wait for the new firmware for that Check out the latest MegaTune release package (mt-r27), it has 1.0.19 firmware which has the tach output working. ---- ---- OLD / solved issues for reference by other users perhaps experiencing simmilar problems Megatune showed wrong voltage: * Only problem is the volt meter in Megatune. It gives 20 volt readings while battery voltage is 13 v. ** You probably missed to calibrate it, adjust battery calibration. Default batt_cal=0xBC (decimal 188) or so *** thanks for that! ---- Ignition problems. Fuel worked but no sprak. * Publish full config, saved by mcd command. * Try to compare your ignition related parameters with a working config, such as MembersPage/MarcellGal/EngineSwap . * As the last chance, start again from the working config, only change what is necessary. * check again if you missed something from GenBoard/UnderDevelopment/FirmwareChanges * Eg. make sure secondary_trigger=02 is used ? Thanks for the feedback! It turned out to be the secondary trigger indeed. ---- Took it for a drive this day. But the engine ran verry lean (afr 1:16) and it appeared all the tables are ampty somehow in megatune. I had this problem with a more recent firware before. Ans switched to a bit older one that seemed to work fine. But now the tables are empty again. Does anybode have any idea how this could be fixed? A: There was a ini update on the magatune page. http://www.vems.hu/wiki/index.php?page=MegaTune <<This package has bug in ini file causing settings lost when updating to ECU, here is [fixed ini file]>> ---- The engine didn't start -> no fuel injection. the pulse width megatune displays is 0 though the crancking pulsewidth is set. And the the req_fuel is set(and all tables are filled with the right values) A: somehow the decel fuel cut rpm was set to 0 rpm after a firmware update. I set is back to 2500 rpm and it started again. Optional: Add document to category: Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.