##      
 ##      
 #####   
 ##  ##  
 ##  ##  
 ##  ##  
 #####   
         

         
   ##    
         
  ###    
   ##    
   ##    
  ####   
         

         
  #####  
 ##      
  ####   
   ####  
 #    #  
 #####   
         

 ___   
(  _`\ 
| (_(_)
|  _)  
| |    
(_)    
       
       

  ###    
   ##    
   ##    
   ##    
   ##    
   ##    
  ####   
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
'''The car''' The project car is a BMW E30 325iS with a M20 3.0 litre stroker engine and T04E turbo. The stock Motronic 1.3 system is not good enough for this application, and it has been decided to install a Genboard. Many details will be the same as for the installation of MembersPage/GergelyLezsak. ---- '''Engine details''' Some of these things are still not decided upon: * Engine: M20B25 , 6 cyl inline, 12 Valves, SOHC. * Primary trigger: Stock 60-2 VR crank-trigger. * Ignition system: Single coil, mechanical distributor. * Idle control : Stock solenoid, two coils - only one used. ** I heard that both coils must be used, "A" powered to decrease opening and "B" used to increase it * Fuel injectors: 32.5 pound * TPS: Yet to be determined. Most likely a post 90's BMW one * IAT: Yet to be determined. * CLT: Stock coolant sensor has NTC curve 2.5kOhm@20C. (NTC's are normally rated at 25C ... not a big difference though) '''Issues''' * '''TPS''' needs to be converted to potentiometer-style for best result. Resistor network cold be hacked together to get three unique positions or a modern TPS could be mounted. * There is no stock '''IAT''' with the AFM gone. It could be custom made with a NTC thermistor (found in Webshop) or maybe a commercial GM/Delco IAT sensor ($16 at Summit Racing). * Fuel injection needs to be sorted out, this depends on keeping the stock harness or building new one which wires to separate injector drivers for each injector. ---- '''Genboard wishes and details''' The assembled unit should be configured like: * Primary trigger: VR sensor / 60-2 wheel * Secondary trigger: Currently no cam sync, but prepare the board for Hall. * Low voltage flyback. * One channel EGT mounted with flying loom, see below. * Knock is also mounted for most v3.3 (and for all v3.3 in EU stock at the moment) '''Yet undecided on this feature.''' * Stepper chip is not needed, BMW uses a solenoid valve which can be controlled through other means. * Deliver with TO220s clamped to case. '''Flying loom for LCD''' Is the connector on the loom of type '''DSUB9 (female)''' or '''DB9 (male)'''? The LCD connector on the ECM is DB9 male (so noone stuffs RS232 to it instead of the RS232 connector that is female on the ECM ). There is often confusion as to which is male and female. The '''newly proposed pinout used''' from GenBoard/BuildProcedures/LCDconnect. The display that will be used ''does not need negative voltage for contrast'' . '''EGT conn''' * K-compensational cable soldered to the board. * Together with the small filtering cap (we use 0805) of almost any value (10..220nF probably best) soldered at the connection near the AD597AR chip (bottom of the board, at the place where the K-compensational cable meets the board). * K-compensational cable attached as a flying loom out through the end plate (rubber grommet). * K-connector is the rectangular miniature (common), female on flying loom and a separate male connector for later mounting on thermocouple cable end. '''Concerning CHECK OUT''' Had initially "checked out" using the money order/check option for payment. Have now sent a full PayPal payment to specified email address. ---- *WikiAdvert: mailto:yourgo@sympatico.ca
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.