####   
 ##  ##  
 ######  
 ##      
  #####  
         

 _       _ 
( )  _  ( )
| | ( ) | |
| | | | | |
| (_/ \_) |
`\___x___/'
           
           

  _    _ 
 | |  | |
 | |  | |
 | |  | |
 | |__| |
  \____/ 
         
         

______ 
|  _  \
| | | |
| | | |
| |/ / 
|___/  
       
       

         
  ####   
     ##  
  #####  
 ##  ##  
 ##  ##  
  ### ## 
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
All the sensors were connected according the incredibly useful PhatBob's guide: http://www.vems.hu/wiki/index.php?page=MembersPage%2FPhatBob%2FUserGuide Assembled unit came with R232 connector, but it wasn't connected to anything, so I had to solder it to EC18 pins. -------------------------------------------------------------- '''Trigger''' Stock VR cam sensor. It has 24 teeth and 2 additional pickups 180 degrees apart. As I rushed things and ordered assembled unit with secondary trigger - Hall, I had to stick to the initial plan by using only NE signal from 24 teeth wheel and grind two opposing teeth off. Otherwise, as I understand, it would be possible to use unmodified stock trigger as coil-type trigger together with cam-sync (from one of those additional pickups G1 or G2) as secondary. So, in this case 24 wheel cam sensor with opposing teeth missing is represented as 12-1 crank wheel. '''IAT''' FAE 33160 '''Coolant temp.''' Stock. Green connector on the side of the thermostat housing. '''TPS''' Stock. Using only E2, VTA and VC terminals. '''MAP''' External VEMS 400 kPa MAP sensor with temperature and 5v outputs - both seem to be useless at the moment. '''WBO2 Sensor''' I had AEM UEGO kit. VEMS supports specific Bosch LSU4 sensors and it turns out AEM is using the same sensor. Well at least pretty similar Bosch LSU4.2, so I connected it. Very helpful info to figure out wiring: http://wbo2.com/cable/lsuconns.htm. I was able to calibrate it with VemsTune. It appears to work. '''EGT''' From Prosport EGT gauge. '''Knock''' Two stock sensors wired but and not used. '''Coils''' Stock three wasted spark coil packs (one coil for two cylinders 1-6, 2-5, 3-4) driven directly from VEMS 3 ignition channels. EC36 pins: 35,33,34. '''Injectors''' LowZ 550cc RC injectors wired with resistors. '''Fuel pump''' Walbro 255. Stock main relay is activated by the ignition switch on, which provides power to circuit opening relay, which in turn is activated by VEMS - EC36-pin15 connected to stock FC wire. http://www.vems.hu/files/Gachax/FP_relays.png '''IAC''' Stepper outputs isn't working (most likely after my attempts in trying to connect stock unipolar stepper IAC). Anyway Bosch 2 wire IAC is connected currently, but it's very hard to get idle smooth, so it's not for long. '''BC''' Pneumatic valve 3way '''TODO''' - Compare lambda readings to the AEM gauge and maybe figure out the way to display readings on the gauge as well. - Try to get knock sensors working although it might not be possible as they are one wire sensors. - Propper IAC control - Connect tachometer - Connect fans
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.