_   _ 
( ) ( )
| `\| |
| , ` |
| |`\ |
(_) (_)
       
       

   ##    
   ##    
 ######  
   ##    
   ##    
   ##    
    ###  
         

  _______ 
 |__   __|
    | |   
    | |   
    | |   
    |_|   
          
          

  _   _ 
 | | | |
 | | | |
 | |_| |
  \___/ 
        

         
 ##      
 ##      
 #####   
 ##  ##  
 ##  ##  
 ##  ##  
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
The car is an old Ford Fiesta with 650 kg starting weight, the motor is a 2.2 liters Ford Probe '''4 cylinder''' turbo engine. There was some confusing information about * '''next trigger tooth''' another_trigger_tooth=14 in the vemscfg... This (20 decimal) is terribly wrong for a 4 cyl, should be 30 (as in the 4cyl 60-2 configlet in primary trigger dialog) ** it was 30 all the time I was just trying the 6 cylinder setup ---- '''Mechanical stuff''' The modifications in the engine ara 4 H conecting rods and custom pistons, the motor is now 4 cylinder an 2,4 liters, for the first run we are keeping the stock turbo an later we will upgrade. ---- '''Trigger - works with VR now''' I have made the wiring harness but first the car wouldn't start because of no primary trigger signals. (RPM = 0). It turned out '''ECU was ordered with HALL input. After changing to correct VR hw setup''', the engine started to work (see below). SJ2 opened SJ6 closed. (This is '''OK from primary trigger VR''') ---- '''Wiring - Outputs''' '''ignition''' ec36 pin 35 cylinder 1 ec36 pin 34 cylinder 2 ec36 pin 36 cylinder 3 ec36 pin 33 cylinder 4 '''injection''' ec36 pin 7 cylinder 1 ec36 pin 19 cylinder 2 ec36 pin 8 cylinder 3 ec36 pin 20 cylinder 4 ec36 pin 15 fuel pump relay '''Wiring - Inputs''' * ec36 pin 23 flyback * ec36 pin 1 tps middle * ec36 pin 14 coolant * ec36 pin 26 sensor ground * ec36 pin 27 primery trigger * ec36 pin 29 tps supply ---- '''Trigger details''' 60-2 For VR always use '''rising edge''' setting (not falling). * '''sensor resistance=502 ohm''' * '''DC volate = 360 mV''' (measured with ignition on) * optional: AC measurement I will make an oscilloscope of my soundcard => GOOD ! * a triggerlog would be reasonable ** (use 1.1.81 or newer firmware to capture triggerlog) We have changed the primary trigger wheel to another 60-2 tooth wheel but from a factory opel engine, now we have 230 rpm at cranking we will try to start the engine soon http://kepfeltoltes.sektor.hu/feltoltott_kepek/1286734795.jpg http://kepfeltoltes.sektor.hu/feltoltott_kepek/1286734811.jpg http://kepfeltoltes.sektor.hu/feltoltott_kepek/1286734826.jpg We '''finally started the engine. First time we had trigger errors but some adjustments in the trigger settings and the engine started to work.''' The gearbox is isn't finished jet so we couldn't go to a test ride. http://www.vems.hu/files/fiesta/datalog201010161415%20fiesta.xls http://www.vems.hu/files/fiesta/v3.3_n003132-2010.10.16-13.58.06%20fiesta.vemscfg ---- '''Trying to find what is missing''' http://www.vems.hu/files/fiesta/vems.jpg The engine wouldn't start now the spark is not there were I am Does the engine start (as above), or not (as here) ? Please review this page and change / delete obsolete info. I rewired the VR sensor with shielded cable I have trigger signs always but the ignition timing is still not correct. I checked all the settings and I will upload the new setting. I also tried the new 1.1.82 but the same problem is on. '''"B" plan''' The car original ignition was a 24+1 trible vr sensor but to use this I have to change the jumper settings in the vems but I have't find exact descripton of this it only says: * for secondary trigger=VR (when not using the 3-sensor auditrigger), we recommend that EC36/13 is used as sectrig VR input. This way EC18/12 can be used for analog input (0-5V, sensitive mcp3208 input). o The second LM1815 and the related blob at the bottom side under the FETs is needed. * wether you order assembled or assemble yourself, read the recommended econoseal pins at [webshop page] * if I have hall setup for secondary trigger ** and I want a normal (what do you mean by normal ??) VR setup what are the steps ** secondary trigger from HALL to VR: [http://shop.vems.hu/catalog/additional-coil-interface-p-52.html?osCsid=98d2c3d2fff1a60a5f74d0be3555ca61 LM1815 chip] must be soldered, and blob under the TO220 FETs at the bottom of the board (there is only one blob under TO220 FETs, and it indeed comes from the 2nd LM1815 chip) must be soldered on. GenBoard/Manual/InputTriggerHardWare '''I would return thanks for any help with this.''' http://www.vems.hu/files/MembersPage/fiesta/v3.3_n003132-2010.11.21-16.13.56elsokor.vemscfg What would you like to achieve ? Any symptoms you are not satisfied with ?
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.