____  
 / ___| 
 \___ \ 
  ___) |
 |____/ 
        

  _   _ 
 | | | |
 | | | |
 | |_| |
  \___/ 
        

         
         
 #    #  
 #    #  
 #    #  
  #  #   
   ##    
         

    ##   
         
   ###   
    ##   
    ##   
    ##   
 ## ##   
  ###    

______ 
| ___ \
| |_/ /
|  __/ 
| |    
\_|    
       
       

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Engine: Fiat Coupe 2,0 16V Turbo Same engine type like all Fiat group 16V engines. - Displacement: 1995ccm - Bore: 84mm - Stroke: 90mm - Cilinders: 4 in line - Firing order: 1-3-4-2 - Distribution: by belt, DOHC (2 cams in head) - Rotation: right - Wasted Spark ignition - Multi point indirect injection ---------------------------- '''Engine tuned parts:''' - Turbocharger: Garrett GT3076R, (external wastegate), assumed pressure appp. 1-1,5 bar - Bigger throttle body: Diameter: 70mm - NA camshafts (same timing, bigger lift) - Exhaust manifold: tubular type - Bigger IC - Bigger injectors ---------------------------- '''Engine sensors (which are used in my project):''' '''- Crankshaft (Trigger 1):''' VR type, 60-2 teeth '''- Throttle position sensor (TPS):''' Bosch 0 280 122 001 '''- Water temperature sensor (WT):''' -type: negative temperature NTC (appr. 2252 Ohm at 25°C) -mark: Bosch 0 280 130 026 -impedance at -10°C = 9 kOhm -impedance at +20°C : 2,5 kOhm -impedance at +80°C : 0,3 kOhm -voltage: 5V '''- Intake Air Temperature sensor (IAT):''' -type: negative temperature NTC (appr. 2252 Ohm at 25°C) -mark: Bosch 0 280 130 060 ( from Lancia Kappa 2,0 16V Turbo) -impedance at -10°C = 9 kOhm -impedance at +20°C : 2,5 kOhm -impedance at +80°C : 0,3 kOhm '''- Manifold Absolute Pressure sensor (MAP):''' -VEMS internal MAP sensor (On-Board) -Max. pressure: 400 kpa '''- WBO2 Lambda sensor:''' Wideband, Bosch 0 258 017 025 Measured Rcal: 85 Ohm = calibration 149,4 (When did free air calibration, value was 144) '''- Exhaust Gas Temperature sensor (EGT):''' type: VEMS, 6mm ------------------------------ '''Engine actuators (which are used):''' '''- Ignition:''' wasted spark type with 2 coils Coils: Marelli BAE 800B (060708038010) (Fiat Punto,Coupe, Lancia Delta,Thema,Y,...) -Primary coil resistance: 0,54 Ohm -Secondary coil resistance: 7500 Ohm (dwel set to 3ms) -Spark plugs: NGK BP6ET (3 electrodes in circle) '''- Injection:''' Injectors type: Peak & Hold Number of injectors: 4 Resistance of 1 injector: 2,5 Ohm @ 68F Siemens DEKA FI11445, 750 cc/min @ 43,5 PSI Additional series resistor for injectors are used: OEM type, cca 7 Ohm per each injector. PWM-ing settings 25.5 msec, 100% Wiring: injA EC36/7 cyl1 injB EC36/19 cyl2 injC EC36/8 cyl4 injD EC36/20 cyl3 -Fuel pressure: 3 bar '''- Boost Control Valve:''' for this time Manual Boost controller is used '''- Idle valve:''' OEM type, PWM one coil
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.