___   
(  _`\ 
| (_(_)
|  _)_ 
| (_( )
(____/'
       
       

         
         
  ####   
 ##  ##  
 ##  ##  
 ##  ##  
  ####   
         

  ______ 
 |  ____|
 | |__   
 |  __|  
 | |     
 |_|     
         
         

    #    
         
   ##    
    #    
    #    
    #    
   ###   
         

         
         
  ####   
 ##  ##  
 ##      
 ##  ##  
  ####   
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
'''Engine''' Inline 4 cylinder natually aspirated engine. '''Intake''' Stock setup is four 39mm flatslide carburetters. Planned setup is 38mm throttles from a Suzuki GSX-R 600, including the stock injectors. http://pusher.dk/zxr/images/efi2.jpg Note: This is from a GSX-R 1000, but the 600 version is very similar. '''Ignition''' Stock setup is two coil wasted spark. According to my Haynes manual the primary resistance of the is 1.8 to 2.8 ohms. Would that make it suitable for VEMS? It is CDI based ignition setup. Second option: Suzuki GSX-R coil on plug. According to the Haynes manual the resistance of the primary winding is 0.8 - 1.2 ohms, would that make it suitable for VEMS? I think it was Jorgen that told me coils lower than 0.5ohms are unsuitable for VEMS.. but I just want to make sure. Trigger wheel: http://pusher.dk/zxr/images/zxr_ignition.jpg Recent photo of the engine. Two wires run to the pickup coil. That would make it an VR type? '''VEMS''' Diagnose plug (rs232), Bulgin - Micro Buccaneer 400 Series. '''Sensors''' * TPS. According to the Haynes Suzuki Manual the TPS shold have a resistance of 1.1Kohm when closed and 4.3Kohm when open. * MAP * Crank trigger. Almost certain that stock can be used. Most likely VR. (HALL or even optical can be used as well, just find out which type it is: count wires, measure Ohm with DVM, etc..). * CLT * IAT * WBO2 '''Injectors''' According to the Haynes Suzuki Manual the injectors are supposed to have an resistance of 11-16 ohms @ 20C. [MembersPage/PhatBob] I think that we need to have some sort of priority list for the manual. Triggers: Types (Hall, VR, optical, distributor) and configuration (missing tooth, multi tooth, sync etc) Sensors: Water, air, tps, map (manifold fitting guide required) Injectors: High/LowZ ---- Apologies for posting this here, but we should discuss the changes to the manual if we are both to work on it together. Your changes look good, so I don't have trouble with that, it would just help to know what one is doing so the other doesn't change the same things. Meet up on IRC this weekend sometime? When is good for you? Im on IRC most of the time also this weekend. Would like to discuss where we are heading with the manual. I was under the impression that I was the only one working on it... Seems not - which is good :-) Drop me a mail: box _at_ pusher _dot_ dk
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.