__   __
 \ \ / /
  \ V / 
   | |  
   |_|  
        

         
         
  ####   
 ##  ##  
 ##  ##  
 ##  ##  
  ####   
         

         
         
 #    #  
  #  #   
   ##    
  #  #   
 #    #  
         

     #   
         
    ##   
     #   
     #   
     #   
 #   #   
  ###    

         
         
  ###### 
 ##  ##  
 ##  ##  
  #####  
     ##  
    #### 

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
I have access to wiring diagrams for any vehicle available in North American 1983-present. Sometimes I can cross it over to Rest Of World cars. If you need schematics for anything, feel free to email me. alandaeric at hotmail dot com ---- From now, trying to organize thematically by splitting to subpages instead of an unstructured list of all the questions * MembersPage/EricN/Trigger - inputtrigger * MembersPage/EricN/Ignition - ignition advance, ignition output and coil related knowledge * ... * MembersPage/EricN/BuildNotes : list of steps to complete my install from the very start ---- SHOPPING LIST Have: Everything, except I forgot to order the dpak fet GenboardV3.2 1 x TPIC8101DW. Dual-channel acoustic knock sensor interface chip 1 x Stepper driver IC, package: DIP16 9 x FET: FQPF20N06L (FAI) 15A, 1 x DPAK FET for genboard v3.2 '''make sure you use a flyback diode if driving inductive loads with the DPAK FET'''. The flyback diode (eg. BY399 is fast 3A, or 1n4007 is slower 1A diode. ES2J is a fast 2A SMB footprint SMD diode) can live in the harness, or on-board (no dedicated pads!). The lack of flyback diode will ruin the DPAK FET and possibly cause other damage when inductive loads are driven. ---- MY PROJECT Ford 347 stroker- on hold,(taking to long to build car) Temporarily putting it in a 61 404 unimog, mercedes 2.2l straight 6. *Standard GM map sensor *Standard GM ect sensor *Standard GM air temp sensor *Not sure which idle stepper motor, whatever the 1000cfm throttle body comes with (most likely 4-wire GM bipolar stepper) *Bosch WB 02, unless someone tells me the NTK one can be easily substituted. *knock sensor: not installed yet. Any should work that can be bolt on appropriately. Hit the block with a wrench and record sound with notebook soundcard to check it's operation about my_make or config.txt? config.txt contains all of your tables and running settings, and my_make contains settings regarding hardware (enabling LCD, keyboard, WBO2, etc). If you are looking to learn about config.txt, look into the file called global.h, or read through MembersPage/Jimw/Config A lot of settings are also described in the manual. Will this VFD work easily?? http://www.vfdworld.com/techdocs/Noritake_CU20045SCPB-T23A_4x20_VFD.pdf It's a serial VFD, it will not work. You need a paralell interface with a 44080 compatible command set. Note that VFD displays often have small incompatibilities with LCD displays even if they are listed as LCD compatible. ---- '''WISH LIST''' *I would like to have a configureable speedo output. (not for my project) *Drive by Wire, need some serious help with that one.
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.