### ## ## ## ## ## ####
___ ( _`\ | | ) | | | | ) | |_) | (____/'
_____ / ____| | | __ | | |_ | | |__| | \_____|
_ _ | | | | | | | | | | | | | |_| | \___/
## ## ## ## ## ## ##### ## ####
IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now. Visit Preferences to set your user name Summary of change: '''Trigger setup''' for Audi S4, 5cyl Direct Fire engine '''Audi 2,2T AAN engine''' Now with orginal trigger ECM: 3.3 #332 Modified to accept auditrigger Scope messurements are done at ~200rpm *added lm1815 *added 100k resistor at R182 *added wire, ec18pin12 to R90 **measure at lm1815 pin3 that this signal comes through (with scope) **[http://linkopingsmotorsport.se/1029/lm1815pin3.gif Pic] ''I think this signal is inverted, try change polarity. The interference between the triggerpulses, can you zoom in and tell if it is from the crank teeth or just normal noise?'' Noise is from primary trigger /Emil_M **[http://linkopingsmotorsport.se/1029/lm1815pin3_2.gif Pic_2] *added blob at SJ7 ** also scope here to see the signal mix from distributor and sec lm1815 output. **[http://linkopingsmotorsport.se/1029/sj7.gif Pic] **This picture is over longer duration, peak is when i hit startbutton[http://linkopingsmotorsport.se/1029/sj7long.gif Pic] also try to take a log with distributor unplugged, you should see 0x0A for each secondary trigger *Signal at G28 (crankteeth) [http://linkopingsmotorsport.se/1029/G28.gif Pic] *Signal at G4 (crank home) [http://linkopingsmotorsport.se/1029/G4.gif Pic] *Signal at Hall [http://linkopingsmotorsport.se/1029/hall.gif Pic] ---- '''Systematic''' secondary trigger debug. The LM1815 has been removed twice from this board (likely unnecessarily). I suggest '''not to solder back''' the LM1815 (or remove it if it's there or remove anything else) until the actions are planned in wiki (preferrably ask on irc to get them reviewed by someone). '''Hide the solderer, or at max unsolder SJ7 if the LM1815 is on at the moment.''' '''Visual review''' I cannot spot anything suspicious: http://linkopingsmotorsport.se/1029/lmarea.jpg The pad (that goes to 2nd LM1815pin3 through the rc filter) might be shorted to GND with some blob (hard to tell visually). You had the crankhome VR soldered there. * Why was it removed? * make sure it's not shorted to GND when you connect the crankhome VR signal back. RC filter that goes to LM1815pin3 * you replaced 18k with 10k. Good * the cap is original ? or changed? 2.2 nF? We must examine (measure DC voltage with DVM, from GND and from 5V as base) the * IC3 trace. * LM1815pin12 output (don't solder the LM1815 on, and don't remove it if there "at the moment" :-) * the SJ7, the jumper between IC3 and LM1815pin2 ** measure the two sides of SJ7 if SJ7 not soldered With the chip removed, or SJ7 unsoldered, IC3 must be pulled up to appr 4V (min 3V). This is done by 2 pullup resistors. If IC3 voltage is less than 3V (not pulled up sufficiently), * there might be something wrong with the cam-HALL input (grounded?). * try to pull up IC3 to 5V through a 10k resistor, and measure voltage again (to see if it's strongly pulled towards GND, or just "not pulled up".) The LM1815pin14 pulse you talked about (on irc: note that it's easy to misunderstand there) indicates that the LM1815pin3 pulse is sufficient (goes below 0V) to trigger the chip. I find it likely that the HALL pulls the IC3 down, and therefore even when LM1815 releases pin12 output as it should, there is not voltage rise to 3V or above (to trigger the AVR input). Note that the LM1815 does not emit a positive output on pin12, just releases it (open-drain), therefore relies on external pullup. If something (like HALL input, or a solder bubble) "disables" our pullup, we cannot blame the LM1815 chip. ---- All sensors original except for map/iat: Bosch 0 281 002 437 Firmware 1.0.29 00:21 Config http://linkopingsmotorsport.se/1029/config.txt Tables http://linkopingsmotorsport.se/1029/tables.txt It turned out that the '''135 tooth noise to the crankhome is inserted outside the ECM''' (with connector removed, it was still there), in the cable or ground. Even if it might idle after some hacks, finally the noise from crank-VR must be eliminated, hints on InputTrigger/AudiTrigger/TestLM It's unacceptable to use * shared (between crankhome and 135 tooth crank) * or nonshielded * or badly shielded (eg both ends!) cable * or bad ground with this setup There is a problem under investigation: the LM1815pin3 is clamped at 0V (not at -0.3V) for some reason. Take pics, measure voltages on LM1815 pins. (supply too). ---- MembersPage/EmilMalmsten/AudiS/OldPage with 60-2 + camsync. Had runout and very little space to fix triggerwheel ---- '''See also''' * MembersPage/EmilMalmsten Optional: Add document to category: Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.