####   
 ##  ##  
 ######  
 ##      
  ####   
         

         
         
 ######  
     #   
   ##    
  #      
 ######  
         

  ____  
 / ___| 
 \___ \ 
  ___) |
 |____/ 
        

         
         
 ##  ##  
  ####   
   ##    
  ####   
 ##  ##  
         

         
  ####   
 ##  ##  
 ######  
 ##      
 ##      
  ####   
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
have cell add these to the manual: info from electromotive manual on there 60-2 Trigger wheel Specs and clearances. ||Trigger|| |||| ||Allowable|| ||Wheel Size|| ||Air Gap|| ||Out-of-round|| ||2½"|| ||.009" - .010"|| ||.001"|| ||3½"|| ||.011" - .012"|| ||.001"|| ||5"|| ||.018" - .021"|| ||.002"|| ||6"|| ||.024" - .028"|| ||.002"|| ||7º"|| ||.029" - .031"|| ||.003"|| ||8º"|| ||.035" - .038"|| ||.003"|| -------------------------- ||Load|| ||Map|| ||1-Bar|| ||2-Bar|| ||3-Bar|| ||Percentage|| ||Voltage|| ||Kpa|| ||Kpa|| ||Kpa|| ||0|| ||0.00|| ||10|| ||8.8|| ||3.6|| ||5%|| ||0.25|| ||15|| ||18|| ||17|| ||10%|| ||0.50|| ||20|| ||28|| ||33|| ||15%|| ||0.75|| ||24|| ||38|| ||48|| ||20%|| ||1.00|| ||29|| ||48|| ||64|| ||25%|| ||1.25|| ||34|| ||58|| ||80|| ||30%|| ||1.50|| ||39|| ||68|| ||96|| ||35%|| ||1.75|| ||43|| ||78|| ||111|| ||40%|| ||2.00|| ||48|| ||88|| ||127|| ||45%|| ||2.25|| ||53|| ||98|| ||143|| ||50%|| ||2.50|| ||58|| ||108|| ||159|| ||55%|| ||2.75|| ||62|| ||118|| ||174|| ||60%|| ||3.00|| ||67|| ||128|| ||190|| ||65%|| ||3.25|| ||72|| ||138|| ||206|| ||70%|| ||3.50|| ||77|| ||148|| ||222|| ||75%|| ||3.75|| ||81|| ||158|| ||237|| ||80%|| ||4.00|| ||86|| ||168|| ||253|| ||85%|| ||4.25|| ||91|| ||178|| ||269|| ||90%|| ||4.50|| ||96|| ||188|| ||285|| ||95%|| ||4.75|| ||100|| ||198|| ||300|| ||100%|| ||5.00|| ||105|| ||208|| ||315|| http://www.hostdub.com/albums/derrickmd18/map_1.sized.gif http://www.hostdub.com/albums/derrickmd18/map_2.sized.gif http://www.hostdub.com/albums/derrickmd18/map_3.sized.gif ----------- Q: how do you hook up the 2.5 Bar MAP sensor to the genboard v3.2? A: on the board the 6 holes in a straight line are for the MAP sensor. #1 signal, #2 +5V, #3 Ground, #4,5,6 are just there to hold the MAP sensor to the board (don't wire pin 4..6 to any signal electrically). If you want to hook up the Map sensor to a free EC pin so you can mount the MAP sensor offboard just run a wire * from MAPsensor pads pin1 to a free pin (eg. EC18-pin3, or the TPS5V pin, which is free by default) than to the offboard MAPsensor pin1 * and run a wire from the HALLsupply (+5v) to the out-of case MAP-sensor (pin2, +5v) * connect GND to MAP sensor (pin2) ----------- ** learn what these setting do for a distributor setup for a 4 cyclinder motor** global.h shows the meanings of the config bytes/bits. Also see HexaDecimal. Here are the settings: <code> // trigger1, bit0 0:falling/1:rising, bit1 0:toothwheel/1:coil, bit2 0:no filtering/1:filtering primary_trigger=07 # =binary 00000111 so filtering, coil-type (not toothwheel), rising edge # uint8_t secondary_trigger; // trigger2, bit0 0:falling/1:rising, bit1 0:enable/1:disable, bit2 0:no filtering/1:filtering, bit3 0:toothwheel/1:coil, bit4 0:alien advance/1:cam sync, bit5 0:single edge/1:both edges when cranking secondary_trigger=3D # bit1=0 => disable tooth_wheel_twidth1=37 # doesn't matter, because primary_trigger bit1=1 (not toothwheel) tooth_wheel_twidth2=23 # doesn't matter, because primary_trigger bit1=1 (not toothwheel) cam_sync_r_edge_phase=03 # doesn't matter, because secondary_trigger is disabled cam_sync_f_edge_phase=02 # doesn't matter, because secondary_trigger is disabled reset_engphase_after=04 ign_tdcdelay=A2 ign_dwell14=40 ign_dwell6=6C ign_crank_advance=35 ign_out=70 ignchmax=03 # first 4 elements of h[2] (or why not all 8) is set to same ignition channel so only one coil is activated (distributor) engine_off_delay=08 </code>
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.