___ ( _`\ | | ) | | | | ) | |_) | (____/'
## ## ## ## ## ## ##### ## #####
## ###### ## ## ## ###
#### ## ## ## ## ## ## ####
### ### ## ## ## ## ## ## ## ## ### ##
IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now. Visit Preferences to set your user name Summary of change: About time I got started... I have a TVR Griffith 500. It's a great car, but could be so much better with the right engine management. My aims are to: *Increase my knowledge of engines and mapping *Make the car easier to maintain and modify *Avoid potential problems with obsolete parts *Gain more power from the engine while using less fuel :-) *Aid with the development of VEMS '''A few words on the car''' http://www.aqyz05.dsl.pipex.com/griff_at_vw.jpg It's a light (1078kg) 2 seater convertable with a 5 litre Rover v8 engine (only 2 valves per cyl :-( ) made by a small company in Blackpool. There are no active safety features at all, so you have to drive it properly. Modifications to date are uprated suspension, uprated brakes, polybushes and a large alloy radiator. '''VEMS setup''' Since I'm very time limited for the moment, I've gone for a fully assembled genboard 3.3 with all the bells and whistles. I plan to have: *the usual sensors (MAP, IAT etc...) *fully sequential ignition and injection *2 WBO2s *dual knock sensor (even having 1 is an improvement!!) ** 1 acoustic is supported, 2 channels require firmware mod ** Ion Sensing needs new hardware ** OK, forget ION sense for now. 1 acoustic is good enough. *EGT '''Trigger setup''' Primary: 36-1 tooth wheel on crank, and Ford VR sensor Secondary: modified distributor with hall sensor - the advance and reterd mechanism will be locked and the factory sensor for the timing will be modified to produce one pulse per rotation instead of the usual 4. (I may make this neater in future and put something directly on the cam wheel as this will be 0.01% more efficient ;-) ) '''Order of work''' *Get VEMS up and running in place of the Lucas 14CUX using the basic sensors. This will be injection only, running sequential ignition *Replace ignition system with 8 coilpacks. )Shame Subaru ones don't fit - I've got loads of them.) *Start to add the "extras" like WBO2 *Do some tuning :-D Update on this: *I'm through the first stage of basic sensors and running in sequential mode, but the injectors are not aligned with the valves. *Coils fitted and working. *Some extras added - single WBO2 fitted, waiting for the second one. *Large injectors fitted for future plans. Much better than the standard ones. *Some tuning of ECU done. Car goes quite well! *Performance exhaust manifolds fitted '''Tuning''' New exhaust manifolds will find their way on the car as the original ones aren't the best design. Also, the intake system could be redesigned to use 8 throttle bodies. Plenty of scope when there's a nice ECU dealing with it all. * Working on a new twin throttlebody plenum. Not happy with the 8 TB solutions I've seen yet, so this will do until I have time to plan more. '''Completion Dates''' Target date for having fully complient system for UK emissions tests is November 2006. This is now "unachieved" as I have no cats in the car for the moment. Have coils & big injectors fitted by May '''Achieved''' Running by June '''Achieved''' Fully mapped by July. Ongoing - delay from exhaust problems pushed this to end of July/beginning of August. '''Mapping is "good enough" for the moment''' Rolling Road session booked for beginning of August. Now rolling roaded - the car produced 260 bhp @5500 RPM and 320 ftlbs @ 3000 RPM. Not quite what I wanted, but it highlighted some fundimental problems with the design of the intake manifold & induction system. See the non-vems related pages for more details. New inlet manifold designed and fitted. A little more rolling road time has resulted in a significant improvement. http://www.aqyz05.dsl.pipex.com/313bhp.jpg Shortly after the above run, the clutch died, followed by the diff. This took a couple of months to source parts and repair. Obsolescence is not a nice thing. The torque plot looks a lot cleaner now there's no slip. http://www.aqyz05.dsl.pipex.com/paFW_sml.jpg '''Other plans''' One goal is to reduce the cars fuel consumption. To this end, I will be investigating "displacement on demand" - ie not fuelling certain cylinders depending on the engine loading. This nicely ties in with the actuation routines for traction control - another thing I plan to look at next year. Also considering running on E85 fuel. Update: Nothing new here, other than I've found (but not fitted) the sensors I need. The plan is to fit these during the body-off restoration that is happening this winter. Body-off restoration completed. Car looks like new underneath now. '''Milestones along the way...''' Fitting & testing the crank & cam triggers: MembersPage/DavidBlades/TrigTest Fitting and testing other sensors: MembersPage/DavidBlades/SenTest Injector Setup & Config file: MembersPage/DavidBlades/InjSetup VE, Lambda tables & tuning the fuel: MembersPage/DavidBlades/FuelTest Starting and Warm-up: MembersPage/DavidBlades/StartingWarmup Acceleration Enrichment: MembersPage/DavidBlades/AccelEnrich Idle control: MembersPage/DavidBlades/IdleControl Cooling fan control & other ancilliaries: MembersPage/DavidBlades/FanTest Fitting Ignition system: MembersPage/DavidBlades/IgnSetup Non VEMS related issues: MembersPage/DavidBlades/NonVems Problem page: MembersPage/DavidBlades/RegulatorProblem Testing the car & ECU: MembersPage/DavidBlades/TestingEcu ---- '''Firmware feature requests''' Ideas for firmware improvements: MembersPage/DavidBlades/DualWb Page about getting TCS inputs: MembersPage/DavidBlades/TCSInputs ---- '''Other Projects that are now in progress''' (Or if it moves, it could do with VEMS) *"Plug and play" harness solution for Subaru Impreza MembersPage/DavidBlades/Subaru *Pugzilla - a mutant Peugeot 309 track & autotest car. MembersPage/DavidBlades/Pugzilla *Nissan 200SX (S14a) - another track day car, but must remain road legal. MembersPage/DavidBlades/The200 *BBE Quark kit car. (You'll never have heard of it - I've not built the prototype yet!) Optional: Add document to category: Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.