_     _ 
( )   ( )
`\`\_/'/'
  `\ /'  
   | |   
   (_)   
         
         

 ###     
  ##     
  ##     
  #####  
  ##  ## 
  ##  ## 
 ######  
         

 _   __
| | / /
| |/ / 
|    \ 
| |\  \
\_| \_/
       
       

      _ 
     | |
  _  | |
 | |_| |
  \___/ 
        

         
         
 ##  ##  
  ####   
   ##    
  ####   
 ##  ##  
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
'''Fitting the Crank Trigger''' There is no appropriate trigger setup on a TVR Griffith. As standard, it uses a 4 tooth wheel and hall sensor in the distributor. I chose a 36-1 trigger wheel with a standard Ford VR sensor. A kit of parts specifically for my engine was available at a reasonable price. Since I don't have time to fabricate such things and can't take the car off the road for that long (it's a daily driver), this was the best option. http://www.aqyz05.dsl.pipex.com/tvr/crank_trig.jpg Fitting the trigger wheel took a whole day, as the crank pulley was held together with Imperial bolts in very awkward positions! (They were supposed to be M8 according to the literature) A tool to remove them was fabricated and they were replaced with M8 cap screws. Apart from this, the physical installation was straight forward. I set the VR sensor to be 1.5mm from the toothed wheel using a feeler gauge. No science here - just an educated guess. Now on to setting the ECU up and testing. '''Setting Trigger parameters''' Here's the parameters I used in the ECU: |Edge:|Rising| |Type:|Multitooth| |Filtering:|Disabled| |TDC after trigger (deg):|58 (estimated from TDC and degree wheel)| |No teeth on wheel:|35| |Trigger tooth:|0| |Next trigger tooth:|9| |Crank min. period:|1875| |Angular width of tooth:|3| |Angular width of missing tooth:|6| Parameters to calculate above: |Rev limit:|7000| |Imaginary teeth:|36| |Missing teeth:|1| |Cylinders:|8| |dec:|3| |Engine Phase in "funny" degrees:|216| '''Testing the Crank Trigger''' Bench testing has already been done, so it's time to put the ECU in the car, but only so it can monitor what's going on. The first time things were connected, the ECU picked up crank rotation and gave a stable speed. The problem is that it is only half the real engine speed. Still, not bad for a first attempt. Trigger works properly now the config is actually set in the ECU and not just on the PC. Doh! * Just need to test the polarity on the VR sensor - it doesn't seem to make much difference to how it runs now. ** it's possible that it runs quite well with reverse polarity, or only counts wheel-err sometimes or above certain RPM. Actually, it is possible to configure multitooth "advanced filter" to work properly with reverse polarity VR for all RPM. But avoid it, and go with the right polarity. Publish InputTrigger/TriggerLog if uncertain. I managed to get a clean "mde40" log file after a lot of bother with the old ECU and doing some maths. The idle was never very good as the old ECU is very crude. Polarity has been established now. As you say, it didn't make much difference - the change in missing tooth length was not much bigger than the RPM change in the engine. Now it's all installed properly. I have a lot of extra noise now, I think it's due to the wires being closer to the old loom. Must check the shielding connection is OK tomorrow and put the sensor ground in properly. Shielding problem has been fixed. I replaced the trigger wire with a better quality wire, and now I get 0 wheel errors. At least it was simple.
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.