### ### ## ## ## ## ## ## ## ## ### ##
## ## ## ## ## ####
##### ## ## ## ## ##### ## ##
_ _ | \ | | | \| | | . ` | | |\ | \_| \_/
# # # # # # # # ## # # #
IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now. Visit Preferences to set your user name Summary of change: = TVR Regeneration = I have 'misplaced' a few parts of the car over the last few years. One of them happens to be it's original VEMS. (It's now doing service in another of my cars...) I have some parts of an old VEMS where the main board is beyond repair, so my cunning plan is to purchase a new v3.8 main board and build up an ECU using the spare case and other parts. I note that a few changes have happened in the last few years so I will sketch out a plan and include some questions to make sure I've got all the changes covered. == Outputs == === Fuelling Outputs === * 8 large Siemens injectors driven from the 8 injector outputs. I used to use IGBTs for these because they proved more reliable. Q: Is it still the case that there are reliability issues with FETs on these outputs? Q: I used to use a 30v transient suppressor diode in the flyback because it worked well. Is there a new scheme I could employ to force the injectors closed faster? (the highZ Siemens injectors do seem slow) Q: If I do this, does it adversly affect the flyback of other output types? * P259 output to drive the fuel pump relay. Q: Has the resilliance of the P259 been improved? I had one or two problems with it in the past (usually my fault!) Q: Is there a convenient way to include within the ECU case some N channel FETs (with suitable flyback protection - relays are inductive after all) to provide higher current outputs? 1A to 2A would be sufficient. * 2 Wideband lambda sensors, connected with decent shielded cable, apart from the power. They will be LSU4.2 because I have a box of these to use up! * Evaporative emissions control valve. Driven from P259, however it is right on the limit of drive capability. (See previous question). Q: Is there a good way of PWMing this output now? I used to use the boost control table for this, but it seems like a waste! (Note that I need the fan and water pump controls for fans, but these won't be PWM driven.) === Ignition Outputs === * 8 Coil-near-plug ignition channels driven from the 8 IGBT outputs. I have both crank and cam sensors so can use them as fully sequential ignition. It looks like nothing much has changed here, and this bit always worked well. === Idle control Outputs === * I have retained the standard 4 pin stepper motor. This is driven using the stepper outputs on the EC18 connector. I see no need to change this. === Misc Outputs === * 2 cooling fans on separate outputs so that they can react to different temperatures. P259 drives relays for these. A FET drive would be nicer if possible. * Tacho output on P259. * Shift lamp currently on P259, but may be replaced by more intelligent instruments. * Check engine / Fault lamp === Summary of Outputs === It would appear I've used all the available outputs on the EC18 and EC36 connectors and still might have one feature that can't be realised. So I need to decide between shift lamp or fault lamp. (It's a TVR, so it will probably need to be the fault lamp!) == Inputs == === Sensor Inputs === * All the usual sensors from the EC36 connector are unchanged as far as I can see. There are some minor changes in triggering, but nothing more than resistor values. * For reference the crank trigger is a VR 36-1 tooth wheel and the cam is a hall based single hole wheel mounted on the cam pulley. Both have been shown to work robustly in the past. * One channel of knock sensing. (Two would be nice, but so far it seems a little unnecessary) Q: This was always connected as a "green wire". The v3.8 board looks like it has dedicated tracks. However, Knock #1 now conflicts with WBO2 #2 Nernst cell on EC18 pin #1. Is this correct? My choice would therefore appear to be to use knock #2 as the main sensor input and limit myself to one sensor, or bring the two sensors out on a separate connector mounted on one of the case ends. The former keeps the wiring simple, but the latter frees an EC18 pin to be a spare analog input, and these are always useful - see later. * Fuel temperature. A useful input to detect heat soak! The car had this from new, so it seems only fair to keep using it on an "anytrim" input. It is to be connected to an analog input on EC18 pin #3. * Wheel speed input. Again I would like to get at least one speed input into the ECU. Q: This is on EC18 pin#8 and conflicts with the WBO2 #2 pump + signal. Is there an alternative pin (for either function) that doesn't require too much rework? Q: Additionally, is the second wheel speed input tracked to a particular EC18 pin? If I want two wheel speed inputs then it might make more sense to output them on another separate connector. * Oil pressure input - mainly for complete logging, but has a benefit for engine safety. * Oil temperature input - mainly for complete logging, but has a benefit for engine safety. === Control Inputs === * Config switch. Currently on EC18 pin #16. * launch control enable. Currently on EC18 pin #12 * Shift cut cluch switch. Currently on EC18 pin #6 * RS232. I am led to belive I can have two of these now. #1 is now tracked to EC18 pin #14 and #15. Q: Does RS232 #2 go only to the pads near the MAX232 chip? === Summary of Inputs === Again, it seems I've used every pin at least once, and will need to introduce some more connectors too. The trick will be to work out what I don't need and what can be done more efficiently. I can then write down a good specification for my spare main board. Optional: Add document to category: Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.