____ 
  / ___|
 | |    
 | |___ 
  \____|
        

 ##      
 ##      
 #####   
 ##  ##  
 ##  ##  
 ##  ##  
 #####   
         

         
         
 ##  ##  
 ####### 
 ####### 
 ## # ## 
 ##   ## 
         

 ___   
(  _`\ 
| ( (_)
| |  _ 
| (_( )
(____/'
       
       

         
         
 ##  ##  
  ####   
   ##    
  ####   
 ##  ##  
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Problem solved Ignition stuck at 10 degrees I have seen this problem a couple of times and Vems hq has a solution for this. It can happen while you upgrade the firmware to newer then 1.1.89 and then you will need a boot loader upgrade. Its easy to due and will only take 5 minutes to cure the problem. Contact Vems.hu for instruction. Ecu nr 35.. Board 3.5 /Peter ---- Ecu needs serialnr ! After we did a firmware upgrade from 1.0.73 to 1.1.92 we got some problems! Every time we switches the ignition off the car and starts it again, the ignition and idle control valve is locked! The ignition is locked at 10 degress, and the IAC valve is locked at 31%.. The only way we can "unlock" it is by "release" the idle or IAC valve in the tools menu.. Any ideas? Here are a log and a config file.. http://www.vems.hu/files/Racezone/Christians%20subaru%201.1.92%20wird%20iac%20+%20ign%20lock.vemscfg http://www.vems.hu/files/Racezone/Christians%20subaru%201.1.92%20wird%20iac%20+%20ign%20lock.vemslog Any Ideas ? Regards Daniel This ECU reports no serial number is it very old, or been repaired (Replaced uc?) I recommend sending for fix in hungary //Emil * board is version v3.1 or 3.2 ? * what is the real serialnumber ? ** orderid ? (or original owner, appr. date of original purchase ?) * do you have parallel port+stk200 (or other cable), or [http://shop.vems.hu/catalog/cable-p-165.html USB avr-ISP cable] to set lock=3c ? After setting lock=3c (AVR "fuse" bit) fixing via serialport is possible (with remote help+token). ** are there any HW-wishes ? Like retesting it, trigger modification (C103 value ?? - if sectrig=HALL?), more analog inputs, protected wheelspeed input(s), exhaust-cam trigger, etc... ? If yes, then [http://shop.vems.hu/catalog/retest-repair-p-103.html retest-repair] might be best anyway. ----- Always use Rising edge of primary trigger when using missingtooth pattern. You should be using this trigger reference tooth table: 0. 18 1. 0 2. 18 3. 0 And ignition outputs in use: 03..00 and the following order: 0. Ignition output 0 1. Ignition output 1 2. Ignition output 0 3. Ignition output 1 Your engine just runs on 2 cylinders Try this config: http://vems.hu/files/ErikEnglund/Configs/subaru.vemscfg It may have something to do with Mat dependent retard, although its disabled. Connect a MAT sensor. Try 1.1.95 firmware, and maybe start with a fresh config and just add the settings thats essential for your engine. Remember to strobe your ignition again. . Erikk
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.