#### ## ## ## ## ## ## ####
_ _ | \ | | | \| | | . ` | | |\ | \_| \_/
###### # ## # ######
_____ |_ _| | | | | _| |_ |_____|
### ## ## ###### ## ## ##
IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now. Visit Preferences to set your user name Summary of change: Assembling the Ver.3.2 GenBoard... Followed MembersPage/JohanEriksson/VerThreeFirmForDummies ---- Q:: did i forgot some parts can't find the problem messured 12v, and 5v on HALL sensor supply, sp2 nessured 12v on 2 pins i think i need to solder more parts but have no clue wich should be added. [http://home.deds.nl/~daihard/genboard/er1.jpg Pic 1] [http://home.deds.nl/~daihard/genboard/er2.jpg Pic 2] Notes: * I recommend to solder the flyback wire to the middle of the flyback trace (so 4 diodes are on one side, and 4 on the other). This results in less heat on the flyback trace (25%) when max 8*1A flyback current flows at a low-impedance setup. For highz it doesn't matter. * make sure the '''TO220 switches''' (FETs, IGBTs) '''do not break off due to vibration'''. The GenBoard/VerThree/CaseAndMounting is more durable considering bibrations. * make sure the '''IGBTs don't contact''' each other. [http://home.deds.nl/~daihard/genboard/er3.jpg Pic 3] [http://home.deds.nl/~daihard/genboard/er4.jpg Pic 4] [http://home.deds.nl/~daihard/genboard/er5.jpg Pic 5] ---- 08-05-2005 fitted the board in to a alubox and fitted separate connectors for: LCD - DB9 PS/2 - keyboard audio jack - serial communication Neutrix 4 pole - WBO2 Neutrix 2 pole - EGT Need to fit Chinch connector for Knock coax cable Need to fit Din 4-5 pole for 3 step steppermotor.[closed,1,2,3 staged open] 24-10-2004 Its working soldered a variable resistor between pin 1 and 3 at the LCD didn't know its that important and thought soldering them as the final touch :) thx... Made the ps2 connection all LED's on the keyboard lightning up on powerup so asume these work aswell. Now starting to check the board with MenuHardwareDebug. 23-10-2004 I'm trying to get the LCD working checked the wiring its ok I'm using a old pc IDE cable even got about 5volts on the nr connection but the lCD isn't showing any sign of live * the LCD is enabled by default * the board is tested OK with my own LCD * the LCD display itself is not tested by me, but it comes tested from the distributor and very unlikely to be faulty * as you didn't talk about squares (that appear when the LCD gets supply and the contrast setting is OK), you either didn't get the GND and 5V right or ( more likely ) you didn't connect contrast. The proper way is to apply a (say 2k7) variable resistor and tune to max contrast, but most often a 270 Ohm to GND is just perfect. (besides the 270 Ohm to GND, also connect a 2k7 to +5V or -8V if the 270 Ohm to GND is not enough by itself). using the following pins and lcd connection Processor side LCD 1 - 13 - 11 - 6 - 2 genB_LCD X - 2 - 4 - 6 - 8 - 10 genB_LCD X - 1 - 3 - 5 - 7 - 9 LCD 4 - 14 - 12 - 5 - - [blank] => X not used Econoseal side I'm not going to match this table to GenBoard/BuildProcedures/LCDconnect ------------------------------------------------- 22-10-2004 '''Its ALIVE''' (resoldered the LED to misc position ) my RS232 cable as good as i could and got a Blinkping and DATA connection YEAHHH :) So now further to step 2: * Testing mdh.. * Connecting the sensors * Testing sensor inputs for functioning * uploading firmware via BootLoader to the processor * More testing ------------------------------------------------- 16-10-2004. After reading and reading the site,things are going alot better' evry thing is fragmentated but hopping from item to item will get me there :). -------------------------- 1) Injection 3 HighZ injectors so need to solder 3 FET's and 3 smb diodes from the resquekit with the stripes facing eachother then soldring the 3 FET's. Well do that tommorow.. -------------------------- 2) Well did the soldering today almost finished... Power: F1 Big black thing in. C72 1uF; D45 KE 22A C101; temp: R9 and R10 2,49K HALL: R55 10 k + SJ2 Ignition: IGBT 3x Q3,Q6,Q9 Injection: FET's 3x Q1,Q2,Q5 and 3diode's Mo 016LV HighZ setup; and Flyback wire EGT: C44 271ohm; SJ9 and AD597 Knock: C17 10nf WBO²: Q18 FET. Stepper: D45 (done with power) and SN754410NE. No need for the 8 flyback diode when SN754410NE is used (it has them internally).There is not even place for them since v3.2. ---- Hmm, powered the board up but no response, found that the V+ to the stepper was blocked through D$5 diode removed this and fitted a wire bridge on 2 places ie F1 and the bridge to the stepper driver. Also got 5v on the HALL sensor output connection, still LCD not working as the Blinkping. Stepperdriver: Soldered C76 and C75 Power: removed D45 replaced with 2 wires. http://www.vems.hu/index.php?page=MembersPage%2FJohanMo I don't fully get the current state of your setup. I added some notes to GenBoard/VerThree/Testing (best to have RS232 working first). Dave noticed: LED doesnt blink because it's in the wrong position: mounted at CL instead of MISC ---- '''Helpful links''' Main Build handout just follow this: * BuildProcedures/SectionThree * Pinout FET's GenBoard/Manual/InitialTesting/VerThree * resistor values: KinderGarden/Components * Injectors Flyback schema: GenBoard/Manual/DDFlyback * Rescuekit easy for identifing GenBoard/VerThree/RescueKit (eg. capacitors values) ---- '''Duplication of GenBoard/Manual/InitialTesting/VerThree''' * [http://www.vems.hu/vems.hu/files/genboardv3/vems_v31_r222_schematic.png Big electric drawing printout png] (png is unsearchable, unlike pdf) * Parts identifing list: http://www.vems.hu/files/genboardv3/megasquirtavr.pnp * Top parts positioning:http://www.vems.hu/vems.hu/files/genboardv3/v32top_r244.pdf * Bottum Parts positioning:http://www.vems.hu/vems.hu/files/genboardv3/v32_botchips.pdf Optional: Add document to category: Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.