|\     /|
| )   ( |
| |   | |
| |   | |
| |   | |
| (___) |
(_______)
         

         
         
  ####   
 ##  ##  
 ######  
 ##      
  ####   
         

      ## 
  #####  
 ##  ##  
 #####   
  ##     
  #####  
 ##  ##  
 #####   

 _   _ 
| | | |
| |_| |
|  _  |
| | | |
\_| |_/
       
       

         
         
  ###### 
 ##  ##  
 ##  ##  
  #####  
     ##  
    #### 

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
TVR Cerbera fitted with AMG M113.980 v8 engine 5500cc. ECU: VEMS 3.6. Firmware 1.1.96 '''Sensors:''' * MAP: vems internal sensor. * IAT: as sold on vems website. * Coolant: bosch * TPS: nissan * Lambda: 1x bosch wideband * Trigger: Bosch VR part number 0241210171 ** no shield on wire. using original engine loom. ---- '''Sectrig:''' * ECU was configured factory sectrig=VR ** home-conversion to sectrig=HALL was attempted, but '''NOT GOOD YET''' * measured 0.37 volts on EC36/17 HALL input when nothing connected ** that is too low ! Should be 3.7V or higher (min 3.0V, realy !) at EC36/13 (or the CPU side of SJ7) * '''REMOVE THE WIRE EC36/13 to the board''', that goes to the 10k before LM1815/pin3 * see the v3.6 sectrig=HALL on GenBoard/Manual/InputTriggerHardWare (v3.6 == v3.7) Bosch Hall HA-P2 part number 0232103111, no shield on wire. Sectrig working well after following above page. ---- Ignition: -8 x coils direct drive from ECU Bosch twin single fire coil 2x1 part number 0221503035 2k ohm in plug leads. all on seperate channels from ecu Injectors: -8 x Standard Bosch for this engine high impedence 13ohms. all on seperate channels from ecu. Outputs: -Fuel pump relay -cooling fan relay -IAC Bosch double solinoid. running on stepper outputs. Timing: Crank trigger 60-2. Missing tooth at 65 deg btdc. Firing order 1-5-4-2-6-3-7-8 Binary code for knock based on firing order: 10110100 (that is 0xb4 , or decimal: 180 ), but if your ignout array does not start with the ignout for cyl1, that needs to be bitwise rotated before using as knock_chan value. * note: if you publish vemscfg or vemslog, we can help, but even the vemscfg (h[2]=... line) or vemslog is not enough to surely tell that, unless the real cylinder numbering - available in new VT for 1.2.x fw - is filled out properly. Just in case, specify ignout - cyl mapping here: * cyl1 EC36/.. * cyl5 EC36/.. * ... https://drive.google.com/folderview?id=0B1bD3kJOFhgZcUJoV3d5bXpETm8&usp=sharing TODO: Knock settings. Runing 2 bosch twin wire sensors. no shield on cable to GND. one wire from each goes to EC18/1 and EC18/2 and both are grounded to EC18/17. is this ok? main problem is software settings, what do i put for (knock chan)? no help menu on vems tune for this. all other input values make sence. many thanks. Contact: chris atbutnossppam kendallengineering.com
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.