##    
         
  ###    
   ##    
   ##    
  ####   
         

         
         
 ##  ##  
  ####   
   ##    
  ####   
 ##  ##  
         

           
     /\    
    /  \   
   / /\ \  
  / ____ \ 
 /_/    \_\
           
           

 _____ 
|  _  |
| | | |
| | | |
\ \/' /
 \_/\_\
       
       

  _______ 
 |__   __|
    | |   
    | |   
    | |   
    |_|   
          
          

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
After mastering(well close) the V2.2 Genboard I have upgraded to the V3.1. The truck is now running quiet well using V3.1. Below is a picture of my beater: http://hotrodders.com/gallery/data/500/4463DSC00576-med.JPG My combination is as follows: Chevrolet 408 cid V8 *Six inch rod engine *Dart Pro 1, 230cc intake, 72cc chamber, 2.08/1.60 valves *Summit Cams - 230in/ex duration at .050, 114 lsa, 480in/ex lift *Edelbrock Proflo MP EFI system: ** 1000 cfm air valve ** upgraded to 50 lb/injectors(high Z) ** pwm idle valve: This is a fairly large GM idle valve. I have not done any research on this yet. I plan on trying to get it tuned after the engine is running so I have been focusing on everything else first. ** GM MAT and CT sensors ** WB O2 in drivers side header ** Hall Effect Mallory Distributor. This distributor has a slotted shutter(or toothed whichever term you prefer) wheel with 8 teeth(one per ignition event) that pass through a Hall Effect sensor. It has an uneven width tooth for #1 used by the edelbrock system for sequential injection. The #1 tooth was more narrow than the others so the ECU could determine injector sequence. Problem is it did not work well as documented by several tuners. I am using the rising edge which is constant and sequential injection. See MembersPage/ChrisGerhardt/ChrisNotes for more details on this. ** I am using the existing ingition amp. The amp is wired with Signal(DB37 pin12), VCC, GND, and a 270ohm resistor between VCC and Signal. After some searching I found that this is a typical GM module that Edelbrock packaged "nicely" in Edlebrock case. The module fires on falling edge and does not control dwell time. I am using MSAVR for that. *76 mm Garrett Turbo - Tial 38mm Wastegate, Turbo XS 35mm BOV, non intercooled (for now) I plan to add a couple injectors for water after everything is up and running. They will be driven by MSAVR and enabled by boost switch. *TH350 Automatic - 3500 RPM 10 inch convertor *Ford 9 inch rear - Narrowed, Moser spool and 33 spline axles, 3.50 M/W gears I will also try to keep some notes on how things go and the most recent emails I am working through on the MembersPage/ChrisGerhardt/ChrisNotes page. My current config, tables, my_make can be found here: http://www.vems.hu/files/ChrisGerhardt/etc_chris_config_r006.zip
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.