### ##  
 #  #  # 
 #  #  # 
 #  #  # 
 #  #  # 
         

 _______ 
(  ___  )
| (   ) |
| |   | |
| |   | |
| |   | |
| (___) |
(_______)
         

  ______
 |___  /
    / / 
   / /  
  / /__ 
 /_____|
        
        

         
         
  ####   
     ##  
  #####  
 ##  ##  
  #####  
         

   ___  
  / _ \ 
 | | | |
 | |_| |
  \__\_\
        

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Ok guys. I need some help. I need to know step by step what to do, to get my engine running. As primairy trigger i'm using a VR sensor with a 60-2 tooth wheel. It's an Opel C20NE engine. The VR+ is connected to EC36pin27. IAT,TPS,CLT is responding nicely. Only need some minor calibration maybe. I use a passive wasted spark coil. That is connected to EC36pin34 and EC36pin36. Can someone help me in the right direction? MembersPage/PhatBob You need to use a timing light to check the spark timing is showing the correct adavance (which is determined by the cranking advance setting). Make sure that there is no power going to the injectors so that the engine doesnt flood. '''I don't have a timing light yet. Is it still possible to start my engine. I just wanna know right now. If I build something that actually runs/idles.''' Have a read of this: http://vems.hu/www.vems.co.uk/VEMSLoom/LoomGuideUnitNNN.doc As it covers the starting proceedure '''Cannot read the .doc file (tried MS Office and OpenOffice)''' --- I'm gonna try to put some information on this page. To help others understand what I have connected to VEMS. And how it is connected. '''Information from Webshop''' *Board version=v3.3 *Serial_nr=709 *pump-=4.16V *wbo2_pump_pw_zero=0x67 *wb02_nernstdc_target=0x85 *pump+=-1.5mV/200 Ohm *AREF=4.9V *(C103=1nF, no D100) --- ||'''Signal'''||'''ECU Pin'''||'''Comments'''|| ||Primairy Trigger = VR ||EC36Pin27||No signal in Megatune|| ||Secondairy Trigger = Hall||EC36Pin13||Don't need this in the beginning|| ||CLT||EC36Pin14||Gives signal in Megatune. Not calibrated|| ||IAT||EC36Pin02||Gives signal in Megatune. Not calibrated|| ||Injector 1||EC36Pin07||Not tested|| ||Injector 2||EC36Pin19||Not tested|| ||Injector 3||EC36Pin08||Not tested|| ||Injector 4||EC36Pin20||Not tested|| ||Coil Cyl 1-4||EC36Pin36||Not tested|| ||Coil Cyl 2-3||EC36Pin34||Not tested|| ||Fuel pump||EC36Pin09||Not tested|| ||RPM out||EC36Pin17||Not tested|| ||TPS||EC36Pin01||Is working correct!|| ||MAP||Internal 250kPa||Seen it working correctly|| ||WB02||EC18 Connector||Did some calibration with Hyperterminal|| --- To keep this page clean I will put all my questions inside a table. Please put you answer inside a row. So it's easy to find an answer to a particular question. ||'''Questions'''||'''Answers'''|| ||What firmware to use?|||| ||Where to get some basic config.txt and tables.txt to start with?|||| ||How do I configure my 60-2 trigger wheel?|||| ||How to set all my inputs and outputs right inside config.txt|||| ||Can someone make a base config for me?|||| ||Is there enough information on my MemberPage to make a config.txt?|||| ||My engine code is C20NE. It is similair to C20XE and C20LET. Some people run it with VEMS. Can I use their config.txt?|||| ||How to test if VEMS can activate my fuelpump?|||| ||How to test if spark plugs will spark?|||| ||Can I test injectors before trying to start my engine?||||
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.