_    _ 
| |  | |
| |  | |
| |/\| |
\  /\  /
 \/  \/ 
        
        

         
 ##      
 ##      
 ## ##   
 ####    
 ## ##   
 ##  ##  
         

         
         
  ####   
 ##  ##  
 ######  
 ##      
  #####  
         

   ____ 
  / ___|
 | |    
 | |___ 
  \____|
        

___  ___
|  \/  |
| .  . |
| |\/| |
| |  | |
\_|  |_/
        
        

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
'''Open Issues ToDo''' I am trying to get multiple spark and injection events per crankshaft revolution with a 12-1 toothed wheel and having no luck. '''Q''' Can someone advise as to which config value may be driving the problem. I currently have requested Ign0 and Inj 1 to fire (hopefully multiple times per crankshaft revolution). '''A''' Bill you have another trigger tooth set to an inproper value, since you have a 12-1 wheel (i assume this is on crank) you have to set another_trigger_tooth to (n_teeth_on_wheel + n_missing teeth) / (n_cyl / 2), in your case. However that would leave you with the same situation you have now, the wheel must be on cam then ? In that case configure another_trigger_tooth = 06 - DB Thank You <code> primep=1A primep_temp_scaling=A0 cwl=46 cwh=46 cranking_thres=05 awev=C0 awev_temp_scaling=19 awc=30 req_fuel=1A divider=01 alternate=11 injopen=19 injocfuel=20 injrampup_battfac=FF injpwm=FF injpwmt=FF injpwm6=00 rpmk[0]=17 rpmk[1]=70 decel_fuelcut_thres=FF overrun_fuelcut=FF overrun_fuelresume=0F rev_limit=5A config11=70 config12=80 config13=06 primary_trigger=01 secondary_trigger=02 tooth_wheel=0B trigger_tooth=04 another_trigger_tooth=18 crank_minper=50 tooth_wheel_twidth1=0A tooth_wheel_twidth2=14 cam_sync_r_edge_phase=FF cam_sync_f_edge_phase=FF reset_engphase_after=F0 ign_tdcdelay=88 ign_dwell14=78 ign_dwell6=1E ign_crank_advance=20 ign_out=71 ignchmax=07 engine_off_delay=08 inj_stage2_rate=FF inj_stage2_start_tps=FF inj_stage2_start_map=FF toothrel_normal=FF toothrel_missing=FF h[0]=01 01 01 01 01 01 01 01 h[1]=00 00 00 00 00 00 00 00 h[2]=00 00 00 00 00 00 00 00 </code> An example of how CWL, CWH, AWEV, AWEV_Temp..., and AWC affect cranking and afterstart can be found at MembersPage/BillHart/CrankingAfterStart. Recent Questions: MembersPage/BillHart/ProblemHistory for older issues that have been resolved. Projects Underway MembersPage/BillHart/WinMobileLogger Win Mobile platform to Fat32 memory card logger. Looking for SIPR examples, if any, to ease the adding V3.3 query to Win Mobile code. * [http://www.lolachampcar.com/Outside%20Pages/VR_Emulator.htm VR_Emulator] is a parallel port based Op-amp circuit that provides a plus or minus pulse about zero to emulate a VR sensor. You build the Basic routine to generate the crank (and cam)input wave form you need. Drop me a note if you need my QB code as a starter. ** we usually use stereo soundcard nowadays. It has many advantages, like processor overhead is small, amplitude can be varied, code is not hard to port between platforms, and it can even work without any executable (wav-s can be played with standard tools). MembersPage/BillHart/LoggingDongle anyone interested in a small relatively inexpensive logging dongle? *WikiAdvert: mailto:bill@lolachampcar.com
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.