____ 
  / ___|
 | |    
 | |___ 
  \____|
        

   ##    
         
  ###    
   ##    
   ##    
   ##    
  ####   
         

_________
\__   __/
   ) (   
   | |   
   | |   
   | |   
___) (___
\_______/
         

   ###   
  ## ##  
  ##     
 ####    
  ##     
  ##     
 ####    
         

           
     /\    
    /  \   
   / /\ \  
  / ____ \ 
 /_/    \_\
           
           

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Open Issues ToDo NONE at this time Thanks Guys Open Questions Simple Question- Doing a lot of clean-up puts a lot of changes in RecentChanges. Is there anyway to edit this page to remove multiple entries when you have done housekeeping? Genboard/Firmware/Upload says "You can construct a device for 1 Euro in about 5 minutes from a DB25 male connector if you have a PC with parallel port." Is there a schematic of the cable assembly and step by step instructions for doing this? If not, will someone please educate me and I will document it on the Wiki. Recent Questions... GenBoard/UnderDevelopment/AlphaN says- pw = req_fuel * MAP * VE(RPM, MAP) / lambda(RPM,MAP) * gammae * ego_corr (speed density: config13 bit2=0) pw = req_fuel * VE(RPM,TPS) / lambda(RPM,TPS) * gammae * ego_corr (with alphaN, without MAP: config13 bit2=1) Notes: * the gamma_enrichment is the multiple of warmup, afterstart, airdenfactor, baro, etc... enrichments. ** airden: gas law, appr. 10% enrichment for -30C change in MAT ** baro: there is a linear 4% enrichment for 10% less than normal baro (to compensate for more gasflow caused by lower exhaust backpressure) * the '''lambdacorr table''' (the 1/lambda is stored for efficiency, so we call it lambdacorr not lambda) is '''used as a constant multiplier in open loop mode and closed loop as well'''. This is the only reasonable operation that gets the desired operation when user changes VE table. ** note that in closed loop mode, ego_corr is adjusted by the ego controller (config.ego_ ...) considering the measured lambda and target lambda (VE table) ** in open-loop mode, ego_corr is always 1.0 (stored as 128 inside SRAM) so the ego_corr is not changed according to the measured lambda. * firmware (eg. for v3.x) sample MAP before starting, and store that value (unless it deviates from config.baro more than config.dbaro: in that case, eg. if ECM resets during engine running, we don't believe that baro is 20kPa and config.baro is used). grep baro global.h **uint8_t config13; // c13, bit3:baro bit2:alphan bit1:WBO2 bit0:oddfire ** uint8_t baro; // mean barometric pressure ** uint8_t dbaro; // max difference in barometric pressure MembersPage/BillHart/ProblemHistory for older issues that have been resolved. Projects Underway MembersPage/BillHart/WinMobileLogger Win Mobile platform to Fat32 memory card logger. Looking for SIPR examples, if any, to ease the adding V3.3 query to Win Mobile code. [http://www.lolachampcar.com/Outside%20Pages/VR_Emulator.htm VR_Emulator] is a parralel port based Op-amp circuit that provides a plus or minus pulse about zero to emulate a VR sensor. You build the Basic routine to generate the crank (and cam)input wave form you need. Drop me a note if you need my QB code as a starter. MembersPage/BillHart/LoggingDongle anyone interested in a small relatively inexpensive logging dongle? *WikiAdvert: mailto:bill@lolachampcar.com
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.