____  
 |  _ \ 
 | |_) |
 |  __/ 
 |_|    
        

  _   _ 
 | \ | |
 |  \| |
 | . ` |
 | |\  |
 |_| \_|
        
        

         
         
 ##  ##  
 ####### 
 ####### 
 ## # ## 
 ##   ## 
         

 _______ 
/ ___   )
\/   )  |
    /   )
   /   / 
  /   /  
 /   (_/\
(_______/
         

         
         
  ####   
 ##      
 ##      
 ##      
  ####   
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Open Issues ToDo NONE at this time Thanks Guys Open Questions NONE Recent Questions... GenBoard/UnderDevelopment/AlphaN says- pw = req_fuel * MAP * VE(RPM, MAP) / lambda(RPM,MAP) * gammae * ego_corr (speed density: config13 bit2=0) pw = req_fuel * VE(RPM,TPS) / lambda(RPM,TPS) * gammae * ego_corr (with alphaN, without MAP: config13 bit2=1) Notes: * the gamma_enrichment is the multiple of warmup, afterstart, airdenfactor, baro, etc... enrichments. ** airden: gas law, appr. 10% enrichment for -30C change in MAT ** baro: there is a linear 4% enrichment for 10% less than normal baro (to compensate for more gasflow caused by lower exhaust backpressure) * the '''lambdacorr table''' (the 1/lambda is stored for efficiency, so we call it lambdacorr not lambda) is '''used as a constant multiplier in open loop mode and closed loop as well'''. This is the only reasonable operation that gets the desired operation when user changes VE table. ** note that in closed loop mode, ego_corr is adjusted by the ego controller (config.ego_ ...) considering the measured lambda and target lambda (VE table) ** in open-loop mode, ego_corr is always 1.0 (stored as 128 inside SRAM) so the ego_corr is not changed according to the measured lambda. * firmware (eg. for v3.x) sample MAP before starting, and store that value (unless it deviates from config.baro more than config.dbaro: in that case, eg. if ECM resets during engine running, we don't believe that baro is 20kPa and config.baro is used). grep baro global.h **uint8_t config13; // c13, bit3:baro bit2:alphan bit1:WBO2 bit0:oddfire ** uint8_t baro; // mean barometric pressure ** uint8_t dbaro; // max difference in barometric pressure Projects Underway MembersPage/BillHart/WinMobileLogger Win Mobile platform to Fat32 memory card logger. Looking for SIPR examples, if any, to ease the adding V3.3 query to Win Mobile code. [http://www.lolachampcar.com/Outside%20Pages/VR_Emulator.htm VR_Emulator] is a parralel port based Op-amp circuit that provides a plus or minus pulse about zero to emulate a VR sensor. You build the Basic routine to generate the crank (and cam)input wave form you need. Drop me a note if you need my QB code as a starter. MembersPage/BillHart/LoggingDongle anyone interested in a small relatively inexpensive logging dongle? *WikiAdvert: mailto:bill@lolachampcar.com
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.