_   _ 
 | | | |
 | |_| |
 |  _  |
 |_| |_|
        

    ##   
   #  #  
   #     
 #####   
   #     
   #     
   #     
         

 #       
 #       
 # ###   
 ##   #  
 #    #  
 #    #  
 #    #  
         

   ##    
         
  ###    
   ##    
   ##    
   ##    
  ####   
         

    ##   
   #  #  
   #     
 #####   
   #     
   #     
   #     
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
'''Assembled (Genboard v3.2) #188''' * v3.2 #188 is clamped * internal 2.5bar MAP sensor with frontplate mounted (WebShop codename: VIV type) pneumatic connector * primary_trigger HW for VR signal shaping => no need to change hall type the crank sensor. * secondary_trigger (set for HALL; test before use) * flying loom PS2 * flying loom LCD (DSUB9) connector: for LCD with 0 or positive contrast. -8V is available in the cable on yellow wire (for the rare LCD that reqires negative contrast), but not connected to DSUB pin). GenBoard/BuildProcedures/LCDconnect * Isupply=0.52V/11 Ohm (might change depending on config and attached stuff) * Knock ** EC18-pin2 knock GND ** EC18-pin3 knock signal * RS232 ** EC18 pin14 (to PC) ** EC18 pin15 (from PC) * 2 DPAK FETs mounted (but no onboard flyback on these channels!) * WBO2 ** Upump- = 3.96V ** wbo2_nernstdc_target=9D (=> 0.45V; B0=> 0.52V rel. to pump-) ** '''wbo2_pump_pw_zero=64''' +1.6mV/340 Ohm ** wbo2_pump_pw_zero=63 -7.2mV/340 Ohm ** wbo2_pump_pw_zero=65 +11mV/340 Ohm * '''IMPORTANT NOTICE! Bridge between GND and GND5 is cut. Connect all GND and GND5 connections before powering up''' ---- '''Assembled v3.2 #184 is ''' * unclamped - will be customized * ECxx mounted * TO220 switches mounted + tested * clamping plates, screws, insulatorsheet included * Isupply=0.52V/11 Ohm (might change depending on config and attached stuff) * WBO2 ** Upump- = 3.98V ** wbo2_nernstdc_target=9D ** '''wbo2_pump_pw_zero=65''' +120mV/10kOhm ** wbo2_pump_pw_zero=64 -4.1mV/340 Ohm (almost halfway between 64 and 65) ---- '''Wishlist''' - sent out * MPX4250AP * 1 VIV (2 way) and 1 VVV (3 way) type pneumatic connector * some pneumatic tube (shot, appr 20cm) * screws * Al frontplate * endplate with DSUB windows * DSUB connectors When you get a better picture of what else you'll need, eg. testing stuff for your standalone boards (22Ohm 1.5Watt resistors, LEDs), pneumatic connectors, endplate with DSUB windows, etc.. write above and will be sent for no extra charge. ---- '''See also''' * MembersPage/BengtR
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.