______ 
| ___ \
| |_/ /
|    / 
| |\ \ 
\_| \_|
       
       

  _____
 |__  /
   / / 
  / /_ 
 /____|
       

         
         
 #####   
 ##  ##  
 ##  ##  
 #####   
 ##      
 ##      

 _   _ 
( ) ( )
| |_| |
|  _  |
| | | |
(_) (_)
       
       

  _______ 
 |__   __|
    | |   
    | |   
    | |   
    |_|   
          
          

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
'''Axel Wall, Sweden''' ---- '''Volvo 245 -87''' Engine specifications: * B23 2,3L 4 cyl. * B230FK intake manifold * B230ET injectors (300cc@3 bar, low-Z) * B230F exhaust (so far..) * Head milled 4mm, and the block 0,9mm. 0,725mm squish. * CR: 15 to 1 (????? is this right ?) -Yes :) I am going to use ethanol, and try to get as much out of it as possible. * 6.5 kg flywheel * Saab 900T pressure plate * Pistons and rods weighted, +/- 0,05g * Balanced crank, pullies, flywheel and pressure plate * Coils are BMW COP 0,9 ohm, Direct fire. * Adjustable cam gear. ---- '''Ignition and trigger setup''' EC36 pins: * EC36pin35 - ch0 - coil 1 * EC36pin33 - ch1 - coil 4 * EC36pin34 - ch2 - coil 2 * EC36pin36 - ch3 - coil 3 h[2]= 02 01 03 00 02 01 03 00 Trigger wheel: * 44-2 crank trigger with VR * Drilled into flywheel * Stock was 44-4, 2 missing at each side Cam sync: *An half circle on the "cam gear" (same gear ratio as camshaft) that drives the oil pump (and previously the distributor too) Indstrial style inductive sensor, connected as Hall. *Rising edge 90 degrees before TDC @ cyl #1 (combustion) ---- '''Firmware''' *1.0.15 std. compilation. *R-024 ---- '''Genboard configuration''' [http://www.vems.hu/files/MembersPage/AxelWall/tables.txt tables.txt], [http://www.vems.hu/files/MembersPage/AxelWall/config.txt config.txt] and [http://www.vems.hu/files/MembersPage/AxelWall/megasquirt.msq megasquirt.msq] (Updated 2005-09-30) ---- '''Current problems:''' *how to set the cam sync up? Is this right? cam_sync_r_edge_phase=01 cam_sync_f_edge_phase=02 reset_engphase_after=04 secondary_trigger=19 ---- '''Previous problems''' * The ignition dont work too good.. cyl 1, 2 and 4 fire when cyl 1 and 4 is at BDC (2 at TDC, all at the same time) cyl 3 dont fire. Should i maybe put coil #1 and #4 on EC36-pin 35, and #2 and #3 on EC36-pin 33? and compile without IGN_DUALOUT? ORE, set up with cam-sync? fully seq, and Direct Fire? ** the channel assignment seems good for IGN_DUALOUT. What compiler do you use? Firing 3 outputs simultaneously is really strange (isn't there a HW problem?). ** Parallel connection of the 0.9 Ohm coils can easily ruin the drivers if dwell is configured too high. But if you measure coil (DC-average) current (in function of RPM and VBatt) and take care not to overdrive, it could work. In that case, connect the 2 channels (so 2 ign outputs, eg. ch0 and ch1 are connected, and this drives 2 coil-inputs, coil1 and coil4 that are also connected) in parallel, so firwmare fires one ign output at one time and the other ign-output the other time. This will half the load on one particular IGBT. ignchmax=03 of course. ***The ignition seems to work now! I think it was the bad trigger who made it so strange... and some faultyness in config.. *** I tried to connect the coils in parallel, but it only resulted in that the drivers stayed on, with burned fuses as an result. 2 coils on one driver worked, but I think it can be a little bit to mutch fore the drivers.. * The "false trigger counter" at LCD is counting up every revitation when cranking, maybe because of the strange 44-2 wheel? ** the 44-2 should not be a problem if tooth_wheel=2A (decimal 42) and if the VR polarity is good. See InputTrigger/TriggerLog. 2..3 wheel-error at cranking is not a big problem, if otherwise everything is OK. *** Trigger is working! I put an 100K in series with a cap, according to Emil's instructions, changed the shielding and changed some things in config. now it counts 1-2 wheel-errors at the first crank, so it's working perfectly :) * The injectors stay open, and I could measure 1.65 V over the injectors, they close when I turn the ECU off. ** this sounds a bit bad. Is it possible that the ECM was running without proper flyback or GND5 connection for some time ? ** is it possible you compiled a firmware without "MY_CONF += -D FETDRIVER_INVERTING" in my_make ? *** Yes, that is posible... I will check that too. ** are you using FETdrivers ? ***I use the std. injector drivers. ***The injectors worked for a while (I think...), the fuelcut above (kPa) was set at 0 too.. BUT! now the injectors stay open again, measuring 12V across the injector.. I realy need to check the Flyback. But the FET's dont ground when the ECU is switched off.. I'm verry sure that the ground is good, and have always been. Fly I will check twice tomorrow.. *** Flyback was working as it should, but I smoked 2 injectors, because I didn't remember that the INJFET-x settings fore coolant fan and IAC points to the H (0) table :( So I had to put the spare injectors in, see above in engine spec.
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.