_ _ ( ) ( ) `\`\_/'/' `\ /' | | (_)
## ## ## ## #### ## ## ## ##
_ _ | | | | | | | | | |/\| | \ /\ / \/ \/
##### ## ## ## ## ## # ####
###### ## ## ## ######
IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now. Visit Preferences to set your user name Summary of change: Hi! I'm Attila Szücs livin' in hungary. I own a Suzuki Swift GTi, modified and turbocharged for amateur drag race, although it's still a street legal car. If you want to see pictures about the modification go to [http://www.freeweb.hu/eltix/pos/pic_gallery_hu.html this page]. The text on the [http://pos.eltix.hu webpage] only hungarian ( sorry, don't have time...), but the pics say enough. Now I decided to dump the stock ECU and change to Genboard. There was a few problems to solve: *the idiot trigger wheel *idle air valve *MembersPage/AttilaSzucs/BoostControl ----- '''Trigger''' The "ultimate goal" is to throw out the distributor and change to wasted spark ignition. Will machining missing tooth trigger plate for the crank, and dump the cam sensor along with the distributor. For saving time, I decided to use the existing trigger. It's a VR sensor with 12 '''non equidistant''' teeth on the cam. This pic shows the tooth placing. http://www.freeweb.hu/eltix/pos/Link/trigger2.jpg The point is, every TDC has 3 teeth, a 91, 61 and 6 deg BTDC signal (gaps are 30, 55 and 95 crankdegrees). See InputTrigger/ShortGapTrigger (for firmware settings for this trigger), same family as InputTrigger/SubaruTrigger and MembersPage/FiatStilo So I keep the 91 deg teeth, theese will be the crank trigger signal, and one 61 deg tooth will be the cam sync (secondary trigger). All the other teeth had been cut off, remaining only five. So, 4 teeth will be equidistant, and one other will be the cam sync. Since the firmware didn't support this insane :) setup (added tooth trigger) back than, I made a little hardware for splitting the signal to the primary and secondary trigger input. I reused the LM1815, it's output signal goes to my additional hw, and the splitted signals go to the primary and secondary inputs. This way the primary input sees 4 pulse, the secondary input sees only 1 pulse during every cam revolution. Both configured to "coil-type" inputs. Attached the little PCB to the EC36 connector with some hot melt glue: http://www.freeweb.hu/eltix/pos/Link/trigger1.jpg Not too fancy, but it'll do the trick. And it works! (I'm surprised too :))) ) ----- || Will continue tomorrow :) || ----- '''Question zone''' *Is there any way to change the frequency of the IAC solenoid PWM? The stock IAC solenoid designed for 18Hz PWM and I'd like to keep it, but it doesn't work with the high freq PWM. Unlike the BoostControl, the IAC valve PWM has no frequency (period)-value in config. It's not particularly hard, if your IAC PWM likes low freq, you can look at how it is done for boost. * Take a look around my MembersPage/GergelyLezsak/IdleControl page, and you'll find a vems.c modified to 100Hz idle. I suffered the same problem and it seems working (not configurable or standard however) ** Thanks, I've noticed your solution few weeks ago and will try it but now I have to do some mechanical modifications on the car. I'll have time for firmware change shortly, that includes trying your modification. ----- || '''Hungarian section''' || ----- Hello POS! Meg tudnád mutatni a difitörö VEMS beállitásodat? Udv:Nanassy Peter * Mostanában folyamatosan változik a beállítás, nemsokára felrakom a config-ot. Egyébként a VE és spark táblázatot kivéve "lopott" config, több usertöl összeollózva, nincs még optimalizálva. Ok,elöre is köszi,es gratulalok az eredmenyekhez!Udv:Peter ----- [[! MembersPage/AttilaSzucs MembersPage/AttilaSzucs/BoostControl]] Optional: Add document to category: Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.