##    
         
  ###    
   ##    
   ##    
  ####   
         

         
   ##    
         
  ###    
   ##    
   ##    
  ####   
         

         
         
  #####  
 #       
  ####   
      #  
 #####   
         

         
         
  ### #  
 #   ##  
 #   ##  
  ### #  
      #  
      #  

 _     
( )    
| |    
| |  _ 
| |_( )
(____/'
       
       

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Planning VEMS 3.3 for turbocharging BMW M50B25 engine in an BMW E36. Lives in Sweden Gothenburg. http://medlem.spray.se/andthu/1.jpg '''Enigne Spec:''' *M50b25 without vanos *Je Forged Pistons Compression 8,1:0 *MLS headgaskset 1,8mm *ARP headstuds *500cc injector *Preicison Turbo SC-44 *Tial 38mm wastegate *50mm PPF blow-off. *600x300x75mm intercooler *Sachs heavy pressureplate 240mm *Organic disc 550nm *Walbro 255l/h fuelpump *Primary trigger: VR *Cam Trigger: VR '''Ordered the following 6/11-2005''' *1 x Assembled v3.3 controller (v3.3) * - secondary_trigger HALL * - primary_trigger HALL * - PowerFlyback yes * - MAP connection 400kPa onboard (6x4mm pneumatic) * - ignition driver 6+2 * - Knock and EGT yes * - LCD and PS2 yes *1 x Econoseal18-Wire *1 x EconoSeal36-Wire *3 x Injector connector pincount 2 *3 x Injector connector pincount 3 *1 x LCD4x20 (LCD4x20) Color blue *3 x VEMS sticker Color red *1 x EGT sensor (K-type) (2x90mm) *10 x K-compensational cable *1 x K-thermocouple connector Sex pair *4 x Temperature sensor *1 x Wideband O2 sensor (LSU4) *1 x Wideband connector With wire with crimped wires *1 x DSUBxx connector '''2006-01-10''' The wiring is almost done, 80% done. Have made a table, but unsure about how yo wire the knock A&B. Also unsure about the IAC. Think it's a 2 coil. Q: I measured the TDC after the trigger on the first cylinder: 340 degress. I read: The value should been between 40-60 degress? How should I set this up then? Use another cylinder to refer to? Pin out: ||'''Function''' || '''EconoSeal pin''' || || Sensor power 5V || 36-28 || || Sensor ground || 36-26 || || Power ground || 36-5 || || Power ground || 36-21 || || Power ground || 36-22 || || Power ground || 36-32 || || Flyback || 36-23 || || injector 1 || 36-7 (Injector A) || || injector 2 || 36-19 (Injector B) || || injector 3 || 36-8 (Injector C) || || injector 4 || 36-20 (Injector D) || || injector 5 || 36-9 (Injector E) || || injector 6 || 36-18 (Injector F) || || CLT || 36-14 (CLT Coolant Temp) || || IAT || 36-2 (Intake Air Temp) || || TPS || 36-1 (TPS signal) || || TPS 5v || 36-28 (TPS +5v) || || IAC || ? || || Crank position sensor (vr) || 36-27 || || Cam position sensor (vr) || 36-13 || || knock signal A || ? || || knock signal B || ? || || coil1 || 36-35 (Coil #0) || || coil2 || 36-33 (Coil #1) || || coil3 || 36-34 (Coil #2) || || coil4 || 36-36 (Coil #3) || || coil5 || 36-11 (Coil #4) || || coil6 || 36-12 (Coil #5) || || Fuel Pump Relay || 36-15 || || nernst_cell || 18-13 || || heater - || 18-18 || || pump - || 18-7 || || pump + || 18-9 ||
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.