______ 
 |  ____|
 | |__   
 |  __|  
 | |____ 
 |______|
         
         

  _____  
 |  __ \ 
 | |__) |
 |  _  / 
 | | \ \ 
 |_|  \_\
         
         

         
         
 #####   
 ##  ##  
 ##  ##  
 ##  ##  
 ##  ##  
         

 _____ 
|  _  |
| | | |
| | | |
\ \_/ /
 \___/ 
       
       

__   __
\ \ / /
 \ V / 
  \ /  
  | |  
  \_/  
       
       

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Understand WhatEverYouDoYouDoItAtYourOwnRisk 7 cylinder engine is one I am building from drawing board up for an aircraft that I am also building. ---- hence the '''low rpm as it is direct drive'''. * Static ground revs no more than 2700 other wise the propeller tips will break the sound barrier (inefficient) ** '''Propeller diameter 1.7m''' 2500 RPM most efficient rev * we put as much pitch on prop as to limit revs * also engine internals would not take high rpm (the internal forces go up by the square of the revs) * legs out of bed in the sky causes one to sweat a bit , thats why we use the fan to keep us cool --- '''Injectors''' are out of a Nissan 280z are 2.6 ohms [ barbed tail, will consider changing ] and best idea of cc rate is 270. * we do not recommend low-Z injectors even on ground. Point noted. Will be changing later as I need to remake injection ring. But first I would like to get it fired up. ---- '''Basic info''' * 7 cylinders * 4 stroke * firing order: 1357246 * Injection firing 7246135 * naturally aspirated ? ---- '''trigger''' - HALL recommended * primary trigger = HALL ** pattern= '''7 crank teeth''' rising 38deg BTDC [ can shift if this is not early enough][ sensor gave a better signal on rising,[wide tooth]] * secondary trigger cam= HALL ** pattern,= single tooth rising TDC number 1[was set up for VR] For this (if there are 7 teeth on the crank!): * then this is 14+1 type trigger (14 pulses per cam rev) ** very similar to 12+1 InputTrigger/MultiToothNoneMissing often used on Toyota and Nissan ** often referred to as "coil type" (not missingtooth aka "multitooth") * next trigger tooth = 2 * tooth_width = 51.5 degrees. Since this is less than 64 degrees, early 1.1.x firmware (from around 1.1.12) can drive this, so 1.1.27 firmware seems to be an option ** the 5cyl audi 10+1 has tooth_width=72 (>64) so that requires newer firmware. That requirement does NOT apply. When you confirm that 7 teeth are on the crank we give it some benchtesting. There are 7 teeth on the crank. ---- '''Ignition outputs''' number,=7 stick coils, inductance [not known ] '''Requires power IGBT output''' (not logiclevel) ? The '''current(in function of dwell) measurement-series''' is required for any proper install (even though often jumped over during ground installs). Recording * VBATT * RPM * lambda (if not doing this in fresh air) * dwell * ignition coil (primary circuit) current ** scope is not essential, because the DC mean value is also useful reading for this ** it is best to measure all ignition transformers individually and find any outstanding values. On ground we also decrease dwell to the point of misfire (often 1.2 .. 1.4msec). Finding dwell values from other applications (for same ignition transformers) can be reassuring. ---- Injectors =7 = 225cc High Z [ am expecting 130HP at 2500RPM can you advise on flow rate][Would like reliable idle] '''Discussion''' * Is there a manual directly relating to VemsTune 0.10.14 I am finding it impossible to go forward without better information. ** it has a help. It has many features, but the basic features are not hard to handle. Tutorial is in the works (separate manual other than the help is not planned: everything should be in the help). You will not be able to set the parameters one-by-one. We will use a starting setup, and modify the bits according to your wiring. So: Start by describing your system above, THEMATICALLY organized by subsystem. So we can help you get a starting setup. Note that even the cylinder count is missing ! Fill in this page above. ---- It now seems that the MAP guage on main screen is directly controlled by the movement of the throttle The software is running alphaN, instead of speeddensity, that´s why the mapsignal is the same as TPS/skassa * correct, if set in alpha-N mode (than rather "load") ! You might want to setup a build page on the forum. http://195.159.109.134/vemsuk/forum/index.php In any case your alpha-n rpm must be 0 to the ecu to run speed density. You should find this in the Alpha-N/Speed density settings menu under the Base settings menu Thanks sorted that bit, will consider forum idea tested with the following two configs: http://www.vems.hu/files/AllanFillery/v3.3_n001212-2010.02.08-14.01.12_14+1_1127.vemscfg http://www.vems.hu/files/AllanFillery/v3.3_n001212-2010.02.08-14.10.40_14+1_1167.vemscfg Now it needs more testing.
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.