##    
         
  ###    
   ##    
   ##    
  ####   
         

 _     
| |    
| |    
| |    
| |____
\_____/
       
       

         
         
 ##  ##  
 ##  ##  
 ##  ##  
  #####  
    ##   
 ####    

         
         
 #    #  
 #    #  
 #    #  
 #   ##  
  ### #  
         

  ______ 
 |  ____|
 | |__   
 |  __|  
 | |____ 
 |______|
         
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
I have set up this project page for the issue I have with no injectors or coils firing, after having the ecu repaired (Chip replaced) for pegged exhaust temp @ 1200 deg. [http://vems.hu/files/Audi%20S2%203B%20Alex%20J/ uploaded files] also a trigger log done after I received the ecu back when I was investigating the no start issue. the care is a '''3B engine (harness) using an ANN ecu. pins have been swapped in the motronic55 female connector'''. car was running as you can see from the log I uploaded. Thanx Alex for the proper report with files. We could reproduce, and indeed: with c270 trigger (confirmed by triggerlog), but RPM=0. Shame, but I couldn't spot the config problem (maybe it's a previously unknown deficiency in 1.1.96 ? We'll let you know if we find). But upgraded to 1.2.23 and works like a charm (fired injectors, and 1 ign). * New VemsTune ** Preferences / update ini files manually ** Tools / web tool, 1.2.23 fw * Tools / Firmware update (I used the old, not the wizard, since uploaded full config anyway) : * [http://www.vems.hu/filethingie.php/files/Audi%20S2%203B%20Alex%20J/v3.3_Alex_3B_upgraded_to_1.2.23.vemscfg config file] ( I config uploaded with "Advanced" to both tables, but disabled table swithching explicitely (I usually do that). ** next to it is a short vemslog file captured with a test ECU, with trigger played on bench ** I adjusted CLT ignadjust=0 in each cell ** I lowered TPS accel enrichment a bit, might need a bit more tuning. Although much quicker (25msec, not 100msec as previously), automatic conversion is not possible, minor retune won't hurt ** note that the IGN based IAC is rather agressive window (16/14 deg)... ** Although a strobe verification (for 1 tooth difference) would never hurt, should get you started (camhall inversion didn't happen, so 360 deg (ignout + triggertooth) shift should not be needed). '''AAN ECU serial number is 1450''' : * NO camhall inverter * CEL not connected (to motronic55/pin22) * wheelspeed not connected * '''repair 2014-03-21''' ** upgraded to uhex bootloader ** 2nd knock fixed ** mcp3208 replaced * PTC MAT ** although no MAT error seen during testing, MAT wire was replaced * heater1, injector and IGBT outputs tested with 22Watt lightbulb (not just LEDs) firmware 1.1.95 although 1.1.96 was installed when I received it back. I think I changed it to 1.1.96 just before I removed it to send away. ---- '''Speculation''' * perhaps his new board has camhall invert and old board did not ? ** RPM reading would be fine with inverted camHALL, just ign firing 360 degrees off. (but in the new logs, RPM=0 all the time) * Dave Brul: I do not see any showstoppers in triggerlog or config, other than secondary pulse being very close to primary pulse ---- '''EGT K-thermo tip broken''' * EGT readings lifts significantly when cranking is initiated (from 222 to 768) ** '''most likely cause, EGT tip grounded (broken probe)''' Although this, in theory shouldn't damage the ADC597 chip (which was damaged earlier), who knows... In any case, a new K-thermocouple will be needed. ---- '''Before / After''' Comparing config before/after (the ecu repair): diff -U2 alex18_before_repair.vemscfg v3.3_u001450-A-2014.03.28-17.25.55_after_Repair.vemscfg Suggests: Apparently some innocent calibration differences (eg. nernst dc target was wrong before) but only max_prim_per_sec_count could effect triggering. <code> @@ -43,5 +43,5 @@ battfac=22 kpafac=D0 -kpaoffs=94 +kpaoffs=90 injocfuel=08 injrampup_battfac=FF ... -wbo2_nernstdc_target=80 -wbo2_pump_pw_zero=82 +wbo2_nernstdc_target=84 +wbo2_pump_pw_zero=67 wbo2_calibration=ED wbo2_heater_pid_kp=45 @@ -238,5 +238,5 @@ act_rpm_rpm=FF act_rpm_channel=FF -egt1_cal=4B +egt1_cal=49 als_tks_channel=FF boost_conf=69 @@ -299,7 +299,7 @@ bla_8[0]=65 bla_8[1]=65 -bla_8[2]=65 -bla_8[3]=65 -bla_8[4]=65 +vvti_measure_tooth=00 +max_prim_per_sec_count=FF +sd_logging_mode=3F boost_pwm_max=FF boost_pwm_min=71 @@ -448,5 +448,5 @@ prohibit_config=00 prohibit_h=04 -prohibit_l=DF +prohibit_l=E0 config_switch=07 vtstorage[0]=7F </code> Thanks for the analysis i will give the config with updated firmware a try tomorrow. just for info the car is a 3b engine running 5 individual V8 coils. you might of guessed from the config. Alex
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.