_________
\__    _/
   )  (  
   |  |  
   |  |  
   |  |  
|\_)  )  
(____/   
         

         
         
 #    #  
  #  #   
   ##    
  #  #   
 #    #  
         

         
         
 ##  ##  
  ####   
   ##    
  ####   
 ##  ##  
         

   ___  
  / _ \ 
 | | | |
 | |_| |
  \__\_\
        

 _____ 
/  ___|
\ `--. 
 `--. \
/\__/ /
\____/ 
       
       

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Hi Marcell I have set up this project page for the issue I have with no injectors or coils firing, after having the ecu repaired (Chip replaced) for pegged exhaust temp @ 1200 deg. [http://vems.hu/files/Audi%20S2%203B%20Alex%20J/ uploaded files] There are log files and config before the ecu was sent away. the config file that was on the ECU when I received it back. also a trigger log done after I received the ecu back when I was investigating the no start issue. the care is a 3B engine using an ANN ecu. pins have been swapped in the motronic55 female connector. car was running as you can see from the log I uploaded. ECU serial number is 1450 firmware 1.1.95 although 1.1.96 was installed when I received it back. I think I changed it to 1.1.96 just before I removed it to send away. ---- '''Before / After''' diff -U2 alex18_before_repair.vemscfg v3.3_u001450-A-2014.03.28-17.25.55_after_Repair.vemscfg Suggests: Apparently some innocent calibration differences (eg. nernst dc target was wrong before) but only max_prim_per_sec_count could effect triggering. <pre> @@ -43,5 +43,5 @@ battfac=22 kpafac=D0 -kpaoffs=94 +kpaoffs=90 injocfuel=08 injrampup_battfac=FF ... -wbo2_nernstdc_target=80 -wbo2_pump_pw_zero=82 +wbo2_nernstdc_target=84 +wbo2_pump_pw_zero=67 wbo2_calibration=ED wbo2_heater_pid_kp=45 @@ -238,5 +238,5 @@ act_rpm_rpm=FF act_rpm_channel=FF -egt1_cal=4B +egt1_cal=49 als_tks_channel=FF boost_conf=69 @@ -299,7 +299,7 @@ bla_8[0]=65 bla_8[1]=65 -bla_8[2]=65 -bla_8[3]=65 -bla_8[4]=65 +vvti_measure_tooth=00 +max_prim_per_sec_count=FF +sd_logging_mode=3F boost_pwm_max=FF boost_pwm_min=71 @@ -448,5 +448,5 @@ prohibit_config=00 prohibit_h=04 -prohibit_l=DF +prohibit_l=E0 config_switch=07 vtstorage[0]=7F </pre>
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.