_________ \__ __/ ) ( | | | | | | ___) (___ \_______/
_ _ | | | | | | | | | |/\| | \ /\ / \/ \/
## ###### ## ## ## ###
_ ( ( /| | \ ( | | \ | | | (\ \) | | | \ | | ) \ | |/ )_)
|\ /| | ) ( | | | _ | | | |( )| | | || || | | () () | (_______)
IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now. Visit Preferences to set your user name Summary of change: Running Motronic 55 pin conversion on one S2 with distributor and another with COP (both 3B engines). 1.1.44 has worked well on both. Figured I'd try 1.1.54, but the tables for spark and lambda got messed up in VemsTune every time the VEMS had been turned off. In case anyone else has the same probs, just edit the VemsTune INI-file: Search for "page 3". The table definition array for lambda has 2 entries that look like this: [8X8] - replace the uppercase X with a lowercase x. Search for "page 4". The table definition array for spark has 1 entry that looks like this: [12X12] - replace the uppercase X with a lowercase x. This did it for me. If your OS moans about editing rights, uninstall VemsTune and install it again outside the "Programs" folder or in an entirely different partition. ------------------------------------ UPDATE: 27 OCT 09 Updated the car with distributor to 1.1.62 A few problems with "Acc enrichment" and "Cold starting", but they are all sorted out now, and the car starts and runs great. Idles excellently. TODO: Check if boost develops as expected, and if so, update the other car as well. See '''running vemscfg''' below ---- UPDATE: 29 OCT 09 Still need to fiddle a bit with boost, but I must say that I am very impressed with 1.1.62. My development car (Audi 5 cyl. turbo with distributor) runs better than I had ever hoped for. Great job on the firmware and VemsTune you guys, and many thanks to Peter Jensen for useful suggestions! Here is a pic from my other project, a rallyecross Audi S2 that I have modified with coils from a late model S4 V8. http://www.vems.hu/files/MembersPage/AlexHoy/S2-Top.JPG Almost a direct fit with modest tweaking of the coils and a slight grinding-down of the valve cover. In case anyone wonders what the distributor is still doing there, it has to stay for now because it holds the camshaft sensor. ----------------------------------------- UPDATE: 5. NOV 09 Slight problem with one VEMS box in the race car. When everything is cold, the VEMS seems to get stuck in bootloader, and the VEMS won't start up. After a few tries, it then boots up. If IGN is then turned off, VEMS won't boot right away (IGN back ON) unless I wait about 30 seconds. When the car is warmed up, the problem seems to be gone. The box has 1.1.44, but considering the temperature sensitivity, this seems to be hardware related rather than software related? LCD just shows completely lit line 1 and 3 when the problem occurs. Thanks for any thoughts on this. How '''long is the RS232 cable ? It sounds like a capacitive "loopback"'''. Plug in a DSUB9 male connector with a 10k resistor between GND (pin5) and RX (whichever pin goes from PC to ECU). This should prevent capacitive loopback (we've only seen this with 1.5m+ long serial cable, but ....) Excellent, thanks! The cable is very long. It was routed through to the rear of the propshaft tunnel, but I thought it better to keep it away from high current wires, so it ended up having to be 2.5m or so. ----------------------------------------- Hi Alex any chance I could grab a copy of your vemscfg 1.1.62 please? you can place it in my file area under the Jamo directory ---- '''Running vemscfg config and tables:''' Note: I was just tweaking idle under load (fan on etc.), so that may not run too well, and boost is not done yet. It boosts, but I am not sure if it limits where it is supposed to. Haven't had a chance to test it yet. The file is from the distributor version - don't forget to make changes if you run COP. http://www.vems.hu/files/MembersPage/AlexHoy/Alex_3B_S2.vemscfg Acc enrich and idle are often not trivial to get good. ** note that boostalt_ref table bins are detached from ignadv bins since 1.1.63 - this is very useful in boost_alternate relative mode (VemsTune vemsv3.ini changes apply of course). Other modes and normal (PID) boost output behaviour uneffected. ------------------------------------------ Many thanks it's just for reference, looks a good map congrats you've convinced me to go with 1.1.62 for my ABY ---------------------- It is a bit on the rich side under load, but the thing takes off like a rocket. Killed the original friction disc during the test stages, and it had only 16K miles on it :-O. The torsion springs were squashed and seemed to be lacking about a fourth in length. "Definitely a torque-related failure", as the SACHS dealer put it. Using a diesel block, this is something you will have already addressed, I assume? These engines are capable of producing torque way beyond the capabilities of gearboxes and driveshafts. ---------------------- I'm running a sachs sintered racing clutch, the car will produce roughly 750+ nm of torque at 2 bar boost!. I think however i'll back the boost of to a lower level to preserve the gearbox as noted although the late ABY and RS2 6 speed boxes are quite strong Optional: Add document to category: Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.