_    _ 
( )  ( )
`\`\/'/'
  >  <  
 /'/\`\ 
(_)  (_)
        
        

         
 ##      
 ##      
 ## ##   
 ####    
 ## ##   
 ##  ##  
         

  _  __
 | |/ /
 | ' / 
 | . \ 
 |_|\_\
       

  _   _ 
 | \ | |
 |  \| |
 | . ` |
 | |\  |
 |_| \_|
        
        

      #  
      #  
  ### #  
 #   ##  
 #    #  
 #   ##  
  ### #  
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
'''BMW 6cyl firmware upgrade from 1.0.46. to 1.1.18''' note: It might be a good idea to avoid accented characters in page titles * 6 cylinder ** firing sequence, 1,..... * primary trigger: 60-2, VR * secondary trigger: not used * ignition: 3 power-output channels, wasted spark '''Ignition output channels. PLEASE SORT TO FIRING SEQUENCE, and WRITE CYLINDER NUMBER TO EACH!''' * EC36 Pin10 ignch7 * EC36 Pin34 ignch2 * EC36 Pin36 ignch3 Please '''verify that the chosen channels are power-outputs'''. Measure (with ignition ON, but engine NOT running) that voltage between +12V and the ign outputs is 0 (a logiclevel output pulls down to 0V when inactive, so that would measure 12V !) 1.0.46 firmware works great with * ignchmax=02 * h[2]=07 03 02 07 03 02 .. .. 1.1.18 firmware plan: * ignchmax=05 * h[2]=70 30 20 70 30 20 .. .. * h[1]=28 14 00 28 14 00 .. .. ** important: you might need to rotate either h[1] or h[2] to get the spark to the right cylinder(-pair). Document the wiring above (write cylinder-numbers) so we can give better hints Engine does not start, shows wheel-error. '''Trigger hints:''' * normal tooth width: 24 (=0x18, since 6 degrees) * missing tooth width: 72 (=0x48, since 18 degrees) * engine phase when to reset: 160 (reset_engphase_after=A0), though this should not cause no-start ---- '''Analog input''' * MCP3208 '''ch6''' connected to EC18pin .. ** ALS or launch works well with this (if channel 6 is selected) ** TODO: verify that it measures +5V when not pulled down externally ** measures ... V when pulled down externally with 1kOhm (you can use other resistor from 100 Ohm .. 10k, just document) * MCP3208 '''ch7''' connected to EC18pin .. ** TODO: verify that it measures +5V when not pulled down externally ** measures ... V when pulled down externally with 1kOhm (you can use other resistor from 100 Ohm .. 10k, just document) ** neither ALS nor launch works if channel 7 is selected. What can be the problem ? *** maybe input was killed ? The mcp3208 inputs are very sensitive, connecting to +12V or electrostatic discharge can damageit. Szevasz Marcell! Hogy tudom elküldeni a dump-ot, és a logot. Valahogy nem tudtam bemásolni...
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.