##   ## 
 ## # ## 
 ####### 
  #####  
  ## ##  
         

         
         
 ##  ##  
 ####### 
 ## # ## 
 ##   ## 
 ##   ## 
         

         
         
 ##  ##  
 ##  ##  
 ##  ##  
 ##  ##  
  #####  
         

         
         
  #####  
 ##      
  ####   
     ##  
 #####   
         

  _______ 
 |__   __|
    | |   
    | |   
    | |   
    |_|   
          
          

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
|| [http://www.vems.hu/wiki/index.php?page=MemberPage%2FMilanaPerisic Start] || [http://www.vems.hu/wiki/index.php?page=MemberPage%2FMilanaPerisic%2FEngine Engine] || [http://www.vems.hu/wiki/index.php?page=MemberPage%2FMilanaPerisic%2FTriggerSetup Trigger] || [http://www.vems.hu/wiki/index.php?page=MemberPage%2FMilanaPerisic%2FFuel Fuel] || [http://www.vems.hu/wiki/index.php?page=MemberPage%2FMilanaPerisic%2FIgnition Ignition] || [http://www.vems.hu/wiki/index.php?page=MemberPage%2FMilanaPerisic%2FPics Gallery] || '''Ignition''' Using stock BMW coil and distributor until i got car dyno tuned,then i will switch to wastedspark on this n/a engine,wastedspark should stay for the turbocharged engine as well. Wiring: http://vems.hu/www.vems.co.uk/VEMSUserManual/ConnectingSingleCoil.png * +12v taken from main engine ralay Mcell hints: ** EC36pin35 (i259ch0) is used now. Beware that it's easy to overload the IGBT with distributer and the low Ohm BMW coil. Dwell > 3msec is very dangerous *** I lowered the dwell to 2.5ms,i was familiar with >3ms dangerous... ** consider EC36pin33 (i259ch1) in parallel (2 outputs connected, driving same coil), and configure i259ch1 output and ign_dualout. ** You don't get higher spark energy, but you share the current load between 2 IGBTs. So it becomes less sensitive to a bit higher dwell (than needed). Less likely to fry IGBT. ** if you forget ign_dualout config option, the outputs will not fry just because of the 2 outputs shorted (remember these outputs can only pull toward GND5), but current load will not be shared. *** I will switch to wastedspark 3x2 as soon as i get modul (in a week or two) so i will get rid of this coil,its bad in any way... In the generic user-manual I would recommend using I259/2 (EC36 pin 34) and I259/3 (EC36 pin 36) because it is available even in a box with only 2 ignition outputs. '''Ignition Configuration''' http://www.vems.hu/files/MembersPage/MilanaPerisic/ignition-settings.JPG http://www.vems.hu/files/MembersPage/MilanaPerisic/ignition-outputs.JPG
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.