##    
         
  ###    
   ##    
   ##    
   ##    
  ####   
         

  _____ 
 |_   _|
   | |  
   | |  
  _| |_ 
 |_____|
        
        

         
         
 #####   
 ##  ##  
 ##      
 ##      
 ##      
         

_________
\__   __/
   ) (   
   | |   
   | |   
   | |   
___) (___
\_______/
         

  ____  
 / ___| 
 \___ \ 
  ___) |
 |____/ 
        

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
VemsMT1.0.30rc3.zip First pass at this has the following results * Unzipped, flashed with supplied firmware * Deleted /config/*.mtt * generate_cofig.bat ran -- no errors * upload_firmware.bat -- reports: Precompiled version 12x12 Standard Boost * upload_config.bat -- reports ** config.mtt @2049 char sent ** tables.mtt @ 4017 char sent * Ran Megatune selected 12x12 standard boost ** VE, Spark, lambda table all report 8x8 in megatune '''r028 complete package, with 1.0.23 firmware''' * used standard flash and attempt to install technique. * Initial Firmware flash looks good * Initial generate config / table _.mtt looks good * Upload_config looks odd, config is ~17char ** found that WinTools\makeconfig is not working correctly This is the generated output <code> Mantt mcs bye </code> Ran r30 \Tools on r28 distribution it at least reported errors ( complained about shiftcut) ----------------- Currently under Beta test for emil_ '''VemsMT1.0.34-testingonly.zip''' emil_ provided a download place for me to test. Givens: * I have several versions of MegaTune installed. * I am pretending to be a user for installation and use * I will not be compiling anything -- only precompiled firmware * To test I need a complete zip file that has everything where it needs to be already. * /config with contain default config.txt and tables.txt '''Proposed Check sequence''' Steps to be checked * Unzip file * delete /config/*.mtt * run in the following order ** upload-firmware.bat ** generate-config.bat ( check for valid table.mtt & config.mtt ) ** upload-config.bat ** start provided MegaTune and ensure communication ** run megatune review mode * report errors ** any errors during any of the (3) batch files ** any errors during boot-up and review mode of MegaTune ** any precompiled (8x8 or 12x12) / MegaTune table errors Configuration changes from MegaTune * change primary trigger setup to 60-2 VAG wheel * change injector output to batch * change ignition output to wasted spark * check redline * check fuel pump control output ( INJ fet and S259-5 ) * Trigger unit and make sure it reads values * WBO2 ** Check pump_zero ** Calibrate o2% ** Breath test * Output configuration ** INJ change to 2 or 4 bank outputs re-arranging combinations of outputs ( firmware people should suggest combination checks ) ** ING change 2 or 4 wasted spark setups (ie. wasted spark COP or is this the dual_ign mod??) ------------------------------ Test Results: emil_ asked me to post these results. using 1.0.34 combo. VE in realtime display MAP is constant, RPM varies. Set VE to 131 in all RPM position in particular row (#3 up from bottom) VE varied from 128-133 Set VE in table to 131 in all positions from Row#1 -- Row #5 VE in RT display varied from 129-130 Basic results: * deleted *.mtt files in \config * generate_config.bat reports 2 errors ** iac_integral_speed in config.txt not in global ** did not find launch_rpm in config.txt ** generate_config.bat made *.mtt files ** upload_firmware.bat reports: Precomiled version reports 12x12 standard boost ** flash successful ** turn off advanced filtering and works fine.
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.