____ 
  / ___|
 | |  _ 
 | |_| |
  \____|
        

         
### ##   
 ### ##  
 ##  ##  
 ##  ##  
 ##  ##  
#### ### 
         

 ___   
(  _`\ 
| (_(_)
|  _)  
| |    
(_)    
       
       

         
         
  #####  
 ##  ##  
 ##  ##  
  #####  
     ##  
 #####   

   ##    
   ##    
 ######  
   ##    
   ##    
   ##    
    ###  
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Here you can report issues with your Genboard V3, firmware, tuningprogram or hardware problems. If you dont know, put it under Unknown. '''Firmware:''' *2005-08-29 with firmware 1.0.15 rc1- '''should be fixed in 1.0.16 firmware''' ** boost table, first bin in megatune, alters primep instead, the rest of the table works. ---- '''Hardware: ''' *2005-08-10 - Possible fried injector driver ** 2005-08-29 - This problem was solved, not genboard related. First, try to test for connected flyback * check connected GND5 (measure ohm between GND5 and battery-. Measure voltage between GND5 and GND when 5..10W 12V lightbulb lit through an output: eg. through an injector connector and relevant mdh.0 command, according to the h[0] table). It sounds like you still don't have GND5 connected, and it's supplied through GND (very BAD !). This is the most likely reason when injectors seem to work when injectors are not overlapping, and fail when injector signals are active in an overlapping way (injector duty > 1/ncyl) * verify flyback: DVM, diode mode between the 2 pins of the harness injector connector (check for every injector connector) * check all outputs with 5..10W 12V lightbulb and mdh.. commands. ---- '''Tuningprogram (Megatune):''' * 2005-09-02 ** EGT display (range) is bad, the gauge displays upto 256C (the digital display is good, but the gauge rails out) ** injector duty cycle... is this fixed already ? *2005-06-23 ** Alha-n tuning is not working ? Megatune ->useing MAP not TPS load the VE-Tables. ** Ini file -> vemsv3_v13_r021.zip ** firmware -> 1.0.13 rc3 ** possible solutions: *** Developers are working on making firmware report load instead of the current kpa *** If you are running alpha-n only and not hybrid mode, its possible to modify vemsv3.ini to show TPS in the realtime tuning, write here or memberspage if you need help. ** thanks for the info.I'am useing Alpha-n only, yes I need details how to modify vemsv3.ini Unknown: *2005-06-22 EmilLarsson ** Firmware -> v13rc5, precompiled. ** config + tables http://kombi.ulkhyvlers.net/vems/roland/ **LCD Display works with genboard powered, engine not started, but after the engine is started, it stops working, sometimes blank, sometimes full of rubbish ** possible solution: *** Will try a capacitor between VCC and GND on the display-side
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.