__  __ 
 |  \/  |
 | \  / |
 | |\/| |
 | |  | |
 |_|  |_|
         
         

 _____ 
(  _  )
| ( ) |
| | | |
| (_) |
(_____)
       
       

    ##   
         
   ###   
    ##   
    ##   
    ##   
 ## ##   
  ###    

 _   _ 
| | | |
| |_| |
|  _  |
| | | |
\_| |_/
       
       

  _     
 | |    
 | |    
 | |___ 
 |_____|
        

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Here you can '''link your report''' issues with your Genboard V3, firmware, tuningprogram or hardware problems. Make your report on your MembersPage, and place link in the relevant section (with a "title", so it can be remembered easily). If you dont know the section, put it under "Unknown". '''In the report, include''' at least: * board version, serial Nr. * '''firmware version''' * '''MegaTune version''' (when MegaTune is used at all) * intended config.txt (possibly commented) * '''mcd.txt''' (captured output of Manmcd command.) This is the '''live config'''. Very important, since in a bad case it can be different from the intended config (if you used a global.h from a different firmware version; or there is a MegaTune configuration problem, etc...) * description of the problem * your investigation so far * any ideas to proceed '''The report, to be considered, must contain all necessary info'''. Without the necessary info, question-answer iterations are needed, so solution is delayed (in the best case). ---- '''Hardware: ''' - usually wiring. These are normally answered even if you only use your MembersPage, but if you insist... * ... ---- '''Config:''' - These are normally answered even if you only use your MembersPage, but if you insist... * ... ---- '''Firmware:''' * ... ---- '''Tuningprogram (Megatune):''' * 2005-09-21 iac activation flag is inverted (Fero reported on phone): not sure which one, the (ON/OFF vs. PWM-stepper - likely) or ignition advance based idle active/OFF * 2005-09-02 ** EGT display (range) is bad, the gauge displays upto 256C (the digital display is good, but the gauge rails out) ** injector duty cycle... is this fixed already ? *2005-06-23 ** Alha-n tuning is not working ? Megatune ->useing MAP not TPS load the VE-Tables. ** Ini file -> vemsv3_v13_r021.zip ** firmware -> 1.0.13 rc3 ** possible solutions: *** Developers are working on making firmware report load instead of the current kpa *** If you are running alpha-n only and not hybrid mode, its possible to modify vemsv3.ini to show TPS in the realtime tuning, write here or memberspage if you need help. ** thanks for the info. I'm useing Alpha-n only, yes I need details how to modify vemsv3.ini *Megatune Accel wizard display shows current TPS instead of changespeed of TPS. ---- '''Unknown: cause''' - sometimes hard to tell if it's hardware/wiring or firmware/MegaTune problem *2005-06-22 EmilLarsson ** Firmware -> v13rc5, precompiled. ** config + tables http://kombi.ulkhyvlers.net/vems/roland/ **LCD Display works with genboard powered, engine not started, but after the engine is started, it stops working, sometimes blank, sometimes full of rubbish ** possible solution: *** config.lcd_c0=FF (bit3=1 reinitilizes LCD at leave_cranking) *** Will try a capacitor between VCC and GND on the display-side * ...
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.