|\     /|
| )   ( |
| |   | |
( (   ) )
 \ \_/ / 
  \   /  
   \_/   
         

 _   _ 
( ) ( )
| |/'/'
| , <  
| |\`\ 
(_) (_)
       
       

         
         
  #####  
 ##  ##  
 ##  ##  
  #####  
     ##  
 #####   

         
 ##      
 ##      
 ## ##   
 ####    
 ## ##   
 ##  ##  
         

   _____ 
  / ____|
 | |  __ 
 | | |_ |
 | |__| |
  \_____|
         
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
'''VEMS uses the PS2 clock signal to receive 0/5V wheelspeed frequency signal.''' Became very popular recently. The PS2 firmware uses the PS2 port for keyboard, and launch-RPM is time-based (not wheelspeed). For wheelspeed input to work, the "non-PS2" firmware must be uploaded ( my_make.16x14/vems.hex ). See GenBoard/UnderDevelopment/FirmwareChanges around and after 1.1.53 Use recent VemsTune. [http://shop.vems.hu/catalog/wheelspeed-cable-p-143.html PS2 wheelspeed cable] might come very handy. DSUB9 connector is included, but you might need a connector for your wheelspeed signal (or tap some wire: but it's counterrecommended to tap ABS signal: WhatEverYouDoYouDoItAtYourOwnRisk). For an audi quattro 6 speed gearbox (reed-switch at the front-left wheel shaft, at least in ours) a [http://shop.vems.hu/catalog/injector-connector-p-87.html 3 pin AMP connector] also needed (only pin2,3 used). '''Sensitive pin''' PS2 clock input is a direct CPU pin. It is very sensitive. Either static electricity or 12V will damage the main processor immediately. Customers are advised to request in the WebShop order note: * '''PS2 clock wheelspeed input on EC18/17''' (used to be 2nd WBO2 FET). ** This '''is standard since 2009-08-01 unless you request otherwise (in the order note)'''. ** someone have been using EC18/17 for sensor ground (easy COMM and additional input wiring) and using EC18/8 for the Speed Input. * 4k7 pullup to +5V * 4k7 and 5V1 zener protection on the processor pin * the last steps on MembersPage/GergelyLezsak/AssemblyThreePointFive show a practical layout of the zener and the pullup resistor. ** Excellent news. Anything to protect the ecu from damage saves us time and money! With the 5V1 zener it is less likely to damage it, and an open-collector HALL sensor or a VR signal and a simple NPN inverter (same as CamHALLInverter) can be used to drive the signal (LM1815 is not necessary for this, although that would work too). Care is still needed of course. ---- '''Wheelspeed data usage''' * logging wheelspeed to notebook, or SDcard * sending to AfreshTiny/AimDisplay for well-visible display * boostcontrol - gear dependent boost * '''launchcontrol - wheelspeed dependent rpm-limit''' ---- '''Launchcontrol''' The good old initial launch behaviour with retard and launch-enrichment is still there. But after reaching the first entry in an '''8 entry table (array)''', no retard, no enrichment: 2x8 bytes for '''wheelspeed => RPMlimit'''. Firmware uses interpolation for smooth transitions between table-points. RPMlimit is in 100 RPM unit. wheelspeed is the unit of your choice. Usually: * km/h * or mph * or any other. It really just depends on calibration The same table is time => RPMlimit for the PS2 firmware where wheelspeed is not available. Time is in 64 msec unit. The first and last bin in the table are somewhat special: * Before the first entry is reached, the good old one-value RPMlimit set in config is used and retard and enrichment is applied "Launch RPM vs Road Speed" screen: http://www.vems.hu/files/KevinBlack/VT%20Launch%20RPM%20vs.%20Speed.JPG Note: the '''"launch-active" flag''' in VemsTune only '''lights up when the RPM-limit is reached (not when the button is pressed - this can be confusing)'''. So if you want to test an analog input switchbutton, configure the ALS input to that pin to see that it lights up. ---- '''Temporary note''' - for .ini file tweakers. This section should be cleaned up when these are deployed in both MegaTune and VemsTune 2009-05-xx releases. Direct commands for page15 (launchcontrol wheelspeed=>launchRPMlimit) read/write are [] brackets. * Offset 0..7 are RPM (unit=100 RPM) * offset 8..15 is the wheelspeed (unit of your choice, depends on calibration) Check the mct dump to see if s[0]= and s[1]=... values are set as you expect. ---- '''LaunchRPM vs. Wheelspeed Curve Questions from Kevin''' * How exactly is it activated? Does the analog input need to be used at all? ** yes, to go to launch mode you always need to activate with an analog input. * Or can this rpm curve be enabled permanently so it does not use up the analog input? ** currently there is a launchinput="disabled" but there is unfortunately no "always enabled" setting (same could be useful for ALS too). * Is it possible to have the Launch RPM appear in the Data Logs? ** the RPM appears in the data-log, and sparkcut directly correlates to the difference between real-RPM and launch-RPM * The "Disable Launch Curve" selection box looks to have bugs, it is blank, should say "Enabled". If you select "Disabled" it does not allow you to go back and enable it again. ** we'll look into this. The launch curve is (IIRC) technically disabled by 0 (speed) in the last entry. Than the (1-entry) launch_RPM setting takes effect. ---- '''REST OF THE PAGE IS BRAINSTORMING''' ---- '''Freq to voltage''' - could also be used [http://www.elfa.se/pdf/73/731/07312713.pdf LM2917] frequency to voltage converter to get wheelspeed info on the LCD and for logging. The app note even has a design almost ready for use Is anyone besides me interested in this? Is there any problem with this solution that I am missing? //Emil
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.