____  
 |  _ \ 
 | |_) |
 |  _ < 
 | |_) |
 |____/ 
        
        

         
|\     /|
| )   ( |
| |   | |
( (   ) )
 \ \_/ / 
  \   /  
   \_/   
         

         
### ##   
 ### ##  
 ##  ##  
 ##  ##  
 ### ##  
 ## ##   
###      

______ 
|  _  \
| | | |
| | | |
| |/ / 
|___/  
       
       

         
|\     /|
| )   ( |
| |   | |
| |   | |
| |   | |
| (___) |
(_______)
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
'''This page lists some useful knowhow related to InputTrigger verification''' The InputTrigger is the most important signal in the system. A multitooth trigger, especially the 60-2 contains an extreme amount of information that could be utilized for tuning. However, since many things can go wrong during an install, this page focuses on debugging, examining the trigger events that GenBoard sees. http://www.vems.hu/files/vems/triggerlog.png Eg. * inverted VR signal * unknown position of missing tooth * noise ( GenBoard/Manual/GroundConnections ) * InputTrigger/RunOut * new triggerlog implementation (since 1.1.78) can also log '''secondary trigger timestamps''' (and use CRC checksum) ** so the margin between secondary and primary trigger pulses can be measured without scope. ** This must be minimum 10 crankdegrees from the missing tooth (if a missing tooth wheel) ** or min 10 crankdegrees from the last tooth for other triggers, eg. coil type or InputTrigger/MultiToothNoneMissing. ** Except InputTrigger/AudiTrigger where it's quite close to the previous tooth (often around 1 crankdegree), that is OK. * On newer non-PS2 firmwares the triggerlog can Log the Speed sensor signals and Spark events ** Note: the Speed sensor is not sampled continuously. Groups of 5 pulses seen. This is normal. '''60-2 example log including secondary trigger data''': http://www.vems.hu/files/VemsTune/sectriglogexample_m582.jpg * '''missing tooth is 58 teeth after''' the previous missing tooth ** normally 532 (*4 usec) between teeth, but 1560 (*4usec) for the missing tooth, that is appr 2.93* longer (appr 3 since 2 are missing: good) * '''sectrig pulse is 23 teeth''' (+291 * 4 usec) after the missing tooth (that is 23 + 0.55 toothtime), 116 teeth (=2*58) after the previous sectrig pulse * file was made with VemsTune, Tools / Analyze,record triggerlog / from file ** file was made with brayterm Manmde40 command and 470 RPM signal, but new VT will be able to record from v3 (that worked earlier) ** I installed 2010-06-03 Nightly VT (if there is already a newer nightly, than the rest of the steps is not needed) ** renamed vemstune-c.exe to vemstune-cORIG.exe ** downloaded http://www.vems.hu/files/pacsa/vemsTune_2010-06-04_1024kPabugfix_exeonly.zip and unzipped into vemstune install dir ---- Under firmware 1.1.78 the trigger logging has different method, see: InputTrigger/TriggerLogOld ---- '''See also''' * InputTrigger/RunOut
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.