_    _ 
( )  ( )
`\`\/'/'
  >  <  
 /'/\`\ 
(_)  (_)
        
        

 __   __
 \ \ / /
  \ V / 
   | |  
   |_|  
        

 _       
( \      
| (      
| |      
| |      
| |      
| (____/\
(_______/
         

         
#### ### 
 ##   #  
  ####   
  ###    
 #  ##   
###  ### 
         

  ###    
   ##    
   ##    
   ##    
   ##    
   ##    
  ####   
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
: '''Subaru Trigger''' => See InputTrigger/ShortGapTrigger for config details Works with the (pictures at the bottom) 6 tooth crankwheel and 7 tooth camwheel (and 1.0.x firmware). * see MembersPage/MichaelRichards/Projects/SubaruECU ** Seen on North American Legacy Turbo and the 2.5L SOHC plants (definitely on 99-01 plants, maybe on 02-03 plants and possibly earlier) ---- '''360 teeth not supported''' - the rest needs clarification. (separate page?) *Older Subarus(L-Series) with ECU controlled ignition have Crank-position [http://www.vems.hu/files/MembersPage/SRepo/Subaru%20trigger_plate.jpg Signal disc] in distributor. *360 little holes in outer ring presents Crank-angle in one degree/Percent precision (For engine speed signal) ** 360 pulses not supported. Rob made signal disks with less pulses, maybe they can be installed *Four long holes, are crank angle signal. One of the holes is longer, indicating (possibly) Cyl 1. (Working on it!!) * 36-2-2-2 setup (36 crank teeth, missing 2 teeth BTDC Cyl 1, and 2 teeth twice before BTDC Cyl 3, exact angle needs TBD). Seen on North American 2.2L SOHC plants (99-01 model using 2 teeth cam wheel) as well as other 2.0L/2.5L Turbo plants (most using 4-1 cam wheel) Q: Any ideas how to make it work with genboar v3.0?? A: the 360-3 tooth crankwheel is definitely more than what current firmware can handle (and possibly above what is practical with the chosen inputcapture - but not HW-counting capable - IC1 channel). I suggest to help out in the InputTrigger/AudiTrigger firmware, that board was designed for this. ---- '''Supported :''' Newer subarus (Legacy mark1) have triggers like these: [http://www.vems.hu/files/MembersPage/SRepo/Subaru%20Cam%20sensor.jpg Cam Sensor] [http://www.vems.hu/files/MembersPage/SRepo/Subaru%20Crank%20Sensor.jpg Crank Sensor] 7 tooth cam wheel: http://www.vems.hu/files/hackish/camwheel.jpg 6 tooth crank wheel: http://www.vems.hu/files/hackish/crankwheel.jpg ---- This is a subaru Impreza WRX+sti 2001- 36-2-2-2 http://img.photobucket.com/albums/v41/Denmark/Vems%20pnp%20Impreza/subaru2001-crankwheel.jpg http://img.photobucket.com/albums/v41/Denmark/Vems%20pnp%20Impreza/subaru2001-crankwheelpic.jpg http://img.photobucket.com/albums/v41/Denmark/Vems%20pnp%20Impreza/subaru2001-camwheel.jpg can someone make a trigger setup with this?, firmware 1.0.78 or what´s needed to make a working trigger config? Thanks skassa
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.