_______ 
/ ___   )
\/   )  |
    /   )
   /   / 
  /   /  
 /   (_/\
(_______/
         

  ###    
   ##    
   ##    
   ##    
   ##    
   ##    
  ####   
         

         
#### ### 
 ##   #  
  ####   
  ###    
 #  ##   
###  ### 
         

 __     __
 \ \   / /
  \ \_/ / 
   \   /  
    | |   
    |_|   
          
          

 _   _ 
| | | |
| | | |
| | | |
\ \_/ /
 \___/ 
       
       

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
= InputTrigger/NissanTriggerTesting = This page is historical only (using old config file format ; was made before the window-identifying 360 pulse implementation, has been obsolete for quite some time ). ---- Thanks to Fredrik we now have something to test! == Test Firmware == Using the build firmware I tested on an S14 CAS using a three speed drill press. http://vems.hu/www.vems.co.uk/VEMSInstalls/NissanTrigger/NissanCASTesting.jpg The system was configured with the following files: [http://vems.hu/www.vems.co.uk/VEMSInstalls/NissanTrigger/config.txt config.txt] [http://vems.hu/www.vems.co.uk/VEMSInstalls/NissanTrigger/tables.txt tables.txt] The following datalogs were run at three different speeds: [http://vems.hu/www.vems.co.uk/VEMSInstalls/NissanTrigger/datalog200608281227.xls 1250rpmDatalog] [http://vems.hu/www.vems.co.uk/VEMSInstalls/NissanTrigger/datalog200608281228.xls 2740rpmDatalog] [http://vems.hu/www.vems.co.uk/VEMSInstalls/NissanTrigger/datalog200608281229.xls 5000rpmDatalog] '''Results''' Any movement of the CAS resulted in the fuel pump line becoming activated, which was good. The CAS reported an RPM that was roughly twice that of the drill's adverised spindle speed, which again is good. But there was a problem with the injector and ignition aspect. If I turned the spindle by hand the RPM reading showed around 100rpm and the injector and ignition lights pulsed on the Test light. But when driving from the drill's motor there was a single flash from the cranking pulse and then no injector or ignition activity. By pulsing the motor's switch I was able to maintain a 100-500rpm speed, resulting in correct injector and ignition activity, allowing the spindle speed to increase to its 1250rpm maximum resulted in the correct acitivity continuing for one or two seconds, then stopping. This was an occasional success, with no activity being most common. == Trigger Testing == Please put the details of your trigger configs under '''Configuration Details''' and post any findings on in the '''Test Verdict''' section. === CA18 === '''Configuration Details''' '''Test Verdict''' === SR20 === '''Configuration Details''' '''Test Verdict''' === RB25 === '''Configuration Details''' '''Test Verdict''' === KA24 === '''Configuration Details''' '''Test Verdict''' === VQ30 === '''Configuration Details''' '''Test Verdict'''
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.