#    #  
  #  #   
   ##    
  #  #   
 #    #  
         

         
 ##      
 ##      
 #####   
 ##  ##  
 ##  ##  
 ##  ##  
         

         
         
 #####   
 ##  ##  
 ##  ##  
 ##  ##  
 ##  ##  
         

  ___ 
 |_ _|
  | | 
  | | 
 |___|
      

    ##   
         
   ###   
    ##   
    ##   
    ##   
 ## ##   
  ###    

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
'''Used on Cosworth engines, on several Ford and Lancia cars. We also call this trigger 8+2''' Very similar to 8+1, but we have a second camtooth that is neglected if * primary_trigger=coiltype * '''and''' primary_trigger=fiatstilo is enabled (yes, fiatstilo bit originally for InputTrigger/ShortGapTrigger such as fiatstilo, subaru, but those are configured with missing tooth option, so there is no collision) [http://www.vems.hu/files/Firmware/release/v3_firmware_1.1.21.zip 1.1.21 firmware] (or newer) firmware is needed for this. ---- <code> alternate=03 divider=01 # 4 cyl rpmk[0]=0B rpmk[1]=B8 config11=31 config12=30 softrpm_range=02 # cosworth coiltype, 8+2 with 4 cyl, primary_trigger=23 secondary_trigger=19 tooth_wheel=08 trigger_tooth=00 another_trigger_tooth=02 crank_minper=30 # 0x168 = 360 = 90 crankdegree (4 pulses per crankrot in the 8+2 Cosworth) tooth_wheel_twidth1=68 tooth_wheel_twidth2=01 reset_engphase_after=40 ign_tdcdelay=78 ignchmax=03 h[0]=01 02 04 08 10 20 40 80 h[1]=00 06 04 02 00 00 00 00 h[2]=00 10 20 30 40 50 60 70 </code> Note that this fires ignch3, ignch2, ignch1, ignch0 in this order. You can connect cyl 1,3,4,2 there respectively, or reconfigure for wasted spark for example ignch2 and ignch3 eg.: h[2]=20 30 20 30 40 50 60 70 ---- Engine RPM/TDC Sensor - '''VR type''' The '''crankshaft pulley has 4 identical teeth spaced at precisely 90°'''. The sensor sends a signal to the module whenever a tooth passes a the sensor. From this signal the module determines engine speed (RPM) and the TDC position of each piston (crankshaft position). http://www.cosworth.hu/content/vegyes/vems/crank_sensor.jpg Note that pistons are 180 crankdegrees apart, so half of the pulses do NOT belong to pistons. This means this sensor requires camsync to operate. Not as convenient as a normal Bosch 60-2 or Rover K4-type pattern. The distributor phase sensor (camsync) - '''also VR''' The distributor is driven by the auxiliary shaft as on the standard ohc engine. A phase sensor, located opposite a cam having '''two teeth separated at 90°''' (camdegrees) to each other, is fitted inside the distributor. At the passing of a tooth the sensor delivers a signal to the ECU. This signal is similar to the signal supplied by an RPM/TDC sensor fitted at the crankshaft pulley. ---- '''Generating trigger wav file''' * Needs a signalgen 2007-04-15 (or later) * type: l008 (l as in ''Lancia'''. l008 for normal polarity, L008 for inverted, which effectively makes no difference for this wav) type * for example RPM sweep from 166 .. 7777, 120 seconds long wav file, sectrig position is 23 (that way sectrig pulses clear primary pulses no matter which edge is selected). max amplitude (1000) for both first tooth, and max (1000) for all the rest teeth as well: <code> ./signalgen l008 166-7777 120 23 1000 1000 </code> ---- Thanx to MembersPage/ZoltanAlmasi for documenting the cosworth trigger. http://www.cosworth.hu/content/vegyes/vems/distr_phase_s.jpg The signal from the distributor and the RPM/TDC sensor together enable module to identify the phase of each cylinder. Note: the polarity of both sensors must be investigated. This is simple, but shouldn't be forgotten. And inverted if necessary, considering that the VR input HW senses the 0-crossing falling edge. (internally rising edge is configured when VR is used, since that is the output of the VR chip; but the VR input is always falling edge). Unfortunately '''this trigger arrangement is not currently supported by firmware.''' * with only 1 campulse, it is supported. Short-dwell ignition transformer (or CDI) is required for high RPM * Is the crank-pulley special in some way ? Is there a chance it can be swapped for a ** multitooth pulley? (available in junkyard, as a long-lasting part that lives well beyond the engine) - under investigation... ** 2 pulses, 50..90 crankdegrees TDC would also work (grindoff ?) with 1-pulse camsync, but a multitooth is unbeatable. *** Original setup must workable with ECU swap, so grindoff not possible. * how many engines are planned of this install ? It is possible to add firmware support, but it's not without costs ** I plan to build 3 engine with vems at first, but this engine management system is used by most of cosworth (Sierra Cosworth 3 door, Sierra Cosworth 2wd saloon, Sierra Cosworth 4wd saloon, and big-turbo Escort Cosworth) - cost approx.??? (It will be the finest sollution
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.