___ ( _`\ | (_(_) `\__ \ ( )_) | `\____)
_______ ( ___ ) | ( ) | | (___) | | ___ | | ( ) | | ) ( | |/ \|
### ## ## ## ## ## #### ## ## ## ##
_ _ | | | | | | | | | | | | | |_| | \___/
## ## ## ## ## ## ##### ## ####
IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now. Visit Preferences to set your user name Summary of change: I have access to wiring diagrams for any vehicle available in North American 1983-present. Sometimes I can cross it over to Rest Of World cars. If you need schematics for anything, feel free to email me. alandaeric at hotmail dot com ---- DONE/DOING LIST * MembersPage/EricN/BoardSetup-step by step of putting my board together * MembersPage/EricN/WBSensor - Testing and config * MembersPage/EricN/Trigger - inputtrigger * MembersPage/EricN/Ignition - ignition advance, ignition output and coil related knowledge * MembersPage/EricN/FuelPage - Injector and fuel setup and config * MembersPage/EricN/Sensor - sensor info * MembersPage/EricN/Config - complete config and tables * MembersPage/EricN/BuildNotes : scraps of info not organinzed IT RUNS!!! After months, no, make that years (since before v2.2 came out)of researching, I finally could not wait so I botched together a fuel pump system, installed my wire harness, plugged my v3.3 in and hit the key. Fuel pump running, smell fuel in the engine, but nothing. Then I turned the fuel pump off and cranked for a while figureing it was just flooded when KABOOM, I was sure my exhaust was dust, too bad for it. Shifted the firing order 180 degrees and add a touch throttle and vrooom. Ran like crap but stayed running as long as I kept a touch of throttle. Need to move it now from the front yard onto the driveway so I can weld up the O2 bung and start tuning. ---- SHOPPING LIST Have: Everything GenboardV3.2 1 x TPIC8101DW. Dual-channel acoustic knock sensor interface chip 1 x Stepper driver IC, package: DIP16 9 x FET: FQPF20N06L (FAI) 15A, ---- MY PROJECT Ford 347 stroker- on hold,(taking to long to build car) Temporarily putting it in a 61 404 unimog, mercedes 2.2l straight 6. *Standard Honda map sensor (maybe) *Standard Honda ect sensor *Standard Honda air temp sensor *No iac, just ignition advance idle control *Bosch WB 02 *No knock sensor yet *No egt sensor *24-1 vr sensor mounted in old distributer *LS1 cnp coils ---- Will this VFD work easily?? http://www.vfdworld.com/techdocs/Noritake_CU20045SCPB-T23A_4x20_VFD.pdf It's a serial VFD, it will not work. You need a paralell interface with a 44080 compatible command set. Note that VFD displays often have small incompatibilities with LCD displays even if they are listed as LCD compatible. ---- '''WISH LIST''' *I would like to have a configureable speedo output. (not for my project) *Drive by Wire, need some serious help with that one.[http://ca.geocities.com/vegas251vegas/poker-room-reviews.htm ...] Optional: Add document to category: Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.