#   
         
    ##   
     #   
     #   
     #   
 #   #   
  ###    

         
         
 ##  ##  
 ##  ##  
 ##  ##  
  ####   
   ##    
         

         
         
 ##  ##  
 ##  ##  
 ##  ##  
 ##  ##  
  #####  
         

__   __
\ \ / /
 \ V / 
  \ /  
  | |  
  \_/  
       
       

     ##  
     ##  
  #####  
 ##  ##  
 ##  ##  
 ##  ##  
  #####  
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
'''MAP-board 1.0''' Important: the pinout of '''packaged external sensor''' http://shop.x-dsl.hu/catalog/images/MAPdongles_and_bare_s.jpg can be found on GenBoard/Manual/Wiring/ManifoldAbsolutePressureExternal The "bare" version is ment to be mounted in the ECM case: The adapter is designed to carry the 400kPa MPXH6400 sensor. Motorola packages this nice sensor in SMD only, so a PCB was necessary for a clean install. Output is compatible with the more common MPX4250AP sensor, but '''features 400kPa range''' instead of 250kPa. Recommended for > 130kPa (1.3bar, 18psi) boost. there are some simple extras onboard, like * regulator (so it can be powered from 12V and there is a 5V output) * thermometer (Temperature output) ---- '''Mounting the 5V "bare" version''' The "bare"-board is '''ment to be mounted vertically in the Alubos case, perpendicular to v3.x''' http://www.vems.hu/files/MAF_MAP_BAP/MAP_400kPa_mounting_m.jpg The image is taken before hotmelt is applied (at the connection of the boards and the sensor nipple). When mounting onboard GenBoard/VerThree, for mechanical stiffness: * '''solder all 6 pins (with bent leads)''' of the 90degree header that connects the boards * the sensor nipple points directly towards the "VIV" type pneumatic connector mounted on frontplate: this secures the mounting ** the screwholes are normally not used, at least not to secure the board against v3.x. The sensor would point down (towards the board -would be quite useless) if these screws were used ! * some hotmelt glue (after testing) helps for extra ruggeddness * '''Note that this sensor has small 5x3mm nipple, so''' ** either the smaller 5x3 mm VIV connector is needed (mounts in drill dia=7mm. Rarely used.) ** or '''use VIV6453 pneumatic connector''' (5/3mm on one side and 6/4mm on the other side, it mounts in drill dia=10mm. This is used normally.) ---- '''Internal version is only practical with 5V supply, to match the supply provided by the GenBoard/VerThree header'''. It's possible to order the "bare" board with 12V supply, for other applications, if you really know what you are doing. '''Pinout of the 5V version''' || '''pin nr.''' || '''signal''' || '''range''' || '''note''' || || 1 || MAP output|| 0 .. 4.8V || 20..400kPa || || 2 || GND || 0V || || || 3 || '''5V in''' || 5V || max 10mA || || 4 || temp out || 0.5 .. 4.5V || NTC, similar U(T) as CLT || || 5 || GND internal || 0V || || || 6 || not connected || - || || The first 3 pin is compatible with the MPX4250AP pinout. ---- '''Pinout of the 12V supply version''' '''Important: while the 12V supply is a nice option for the external GenBoard/Manual/Wiring/ManifoldAbsolutePressureExternal, for the internal the 5V is what you likely need when used inside the v3.x case. The 12V is only for special applications, not suitable for direct mounting on GenBoard/VerThree. Note that populated this way, the supply has a wide range, and the '''5V is output, not input. Applying 5V to the 5V output is not supported, it might damage the unit.''' || '''pin nr.''' || '''signal''' || '''range''' || '''note''' || || 1 || MAP output || 0 .. 4.8V || 20..400kPa || || 2 || GND || 0V || || || 3 || '''5V out''' || 5V || max 80mA. Useful for HALL, TPS, etc... || || 4 || temp out || 0.5 .. 4.5V || NTC, similar U(T) as CLT || || 5 || GND internal || 0V || || || 6 || '''+12V in''' || 6.3 .. 16V || || ---- '''See also''' * See GenBoard/Manual/PneumaticTube * GenBoard/Manual * GenBoard/Manual/Config/ManifoldAbsolutePressure * WebShop (see Genboard, sensors)
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.