# ###   
 ##   #  
 ##   #  
 # ###   
 #       
 #       

    ##   
         
    ##   
    ##   
    ##   
    ##   
    ##   
  ###    

 _   _ 
| | | |
| | | |
| | | |
\ \_/ /
 \___/ 
       
       

 __     __
 \ \   / /
  \ \_/ / 
   \   /  
    | |   
    |_|   
          
          

    ###  
   ##    
   ##    
 ######  
   ##    
   ##    
   ##    
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
[http://megasquirtavr.sourceforge.net/manual/Basics.Install.Mechanic.html [Manual: Basics.Install.Mechanic]] Soldering steps reminder list. '''Before mintest''' * big black barrell inductivity (1.5uH 5.4A or blue 3.3uH 8.8A) * quartz 16MHz * main fuse wire * 0 Ohm resistor on the bottom (D45 for stepper?) * -- R154 under the atmega -- (factory populated since v3.3) * -- LCD supply capacitor (C89) 10uF -- (factory populated since v3.3) * -- Big Vbatt capacitor (C72) 10uF (min.25V) 1210 -- (factory populated since v3.3) * Big 18V 1.5kE18 troughole transient suppression diode (bottom of the board) (factory populated SMB on top since v3.3, needs checking ! ) * -- connect the GND bridge -- (not applied since v3.3) * pinheaders for the ISP * do the firmware things and checks (bin/mintest.sh, bin/prog.pl) '''Mintest possible''' at this point * ... * supply voltages * supply current * LCD test requires special connector (since no header) or a bit of experience '''Optional stuff below''' * -- 5V1 protecting zener for trigger1 D14 -- (factory populated since v3.3) * -- 5V1 protecting zener for trigger1 D27 -- (factory populated since v3.3) * configure trigger1 to VR (2 jumpers) * configure trigger2 to HALL (1 jumper) * trigger1 pullup resistor REMOVE (R55) * EC connectors * -- flyback diodes -- (factory populated since v3.3) * flyback airwire (EC36 pin23) * FETs * IGBT * additional brown GND5 airwire on bottom (EC36pin21,pin22) * additional brown GND5 airwire on top (EC36 pin5) * flyback testing: all inj. outputs toward the flyback rail '''airwires to EC18''' * knock * RS232 * MAP signal (if not onboard MAP) * hotmelt '''Stepper''' * stepper chip * stepper capacitor (C75) 1210 (min.25V), 10uF * stepper Vbatt wire in the place of D45 '''knock''' * 4 MHz * TPIC8101DW knock chip '''for LCD that likes -3V contrast''' * -- R112=2k4 -- (factory populated since v3.3) * -- take out the 1k towards GND -- (not populated in factory since v3.3) '''Final tests''' * many * pump- voltage * wbo2_pump_pw_zero * wbo2_nernstdc_target (0.45V between nernst and pump- when WBO2 activated with mde02 or RPM signal) * 64-1 stim-out signal (mstbemsp03) from stepperA (0x36) output, and checking proper operation of all 8 injector and ignition channels with connected LEDs. Requires wasted-spark 16 cyl config with 64-1 wheel ---- A special board is used to test the outputs: http://www.vems.hu/files/genboardv3/MinTest/TestLightDumb_0002_m.jpg With a * 64-1 stim-signal: mst7e msp02 * tooth_wheel=3e * trigger_tooth=00 * another_trigger_tooth=08 * Note: "coil-type" input-trigger works as well, than the above wheel-parameters are not used, and mst3f msp24 command is used to drive the OutputTrigger * alternate=07 * h[0]=01 02 04 08 10 20 40 80 * ignchmax=07 * h[2]=00 01 02 03 04 05 06 07 it's obvious from first glance if there is any irregularity due to: * firmware problem * HW problem (eg. 2 neighboring IGBT-s shorting because of clamping problem) * config problem (eg. bad trigger configuration or fuelcut) Note that this does not substitute the flyback test. The same board can be used for different tasks, for example: * upper (outer 4 + inner 4=total 8) RED as '''shiftlight''' * the other 8 (non-RED, eg. green, blue, yellow and white) LEDs for different status indication: ** fuel-pump active ** variable-intake actuator active ** boost-solenoid active (makes boost-PID tuning easier) ** warmup enrichment active (the output channel for this is not currently configurable) ** finally integral-rail in various PID controllers (idle, boost, WBO2 pump, WBO2 heater, etc...) Note that these indications (although not too complex) are not implemented yet. ** CEL (check engine light) ** '''add your wish here''' ** etc... ---- '''See also''' * GenBoard/Manual
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.