##  ##  
 ##  ##  
 ##  ##  
  ####   
   ##    
         

         
         
  ####   
 #    #  
 #    #  
 #    #  
  ####   
         

  ____  
 |  _ \ 
 | | | |
 | |_| |
 |____/ 
        

         
### ###  
 ##  ##  
 ##  ##  
 ##  ##  
 ##  ##  
  ### ## 
         

         
         
 #####   
 ##  ##  
 ##  ##  
 #####   
 ##      
 ##      

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
VEMS V3.9 AAN is by default Conversion to VR, HALL if ever needed for a non-factory setup. '''InputTrigger/AudiTrigger with camHALL inverter, which means:''' * '''primtrig=VR''' (VR on crank as you prefer, nothing to do there) * '''sectrig=Auditrigger with camHALL inverter''' ** pulling camHALL input = GND or 100 Ohm resistor to GND would allow sectrig=VR to go through unmasked (if sectrig=VR needed) ** '''convert to HALL by:''' disabling the 2nd LM1815 by '''removing''' the sectrig LM1815 (U110 ?) output '''SJ7 solder-blob on the bottom''' (that connects LM1815pin12 output to the microcontroller input pin). This blob is on the bottom, under the FETs. output solderblob at the bottom side under the FETS so that HALL signal will reach the processor and work (VR will be ineffective as a result). Sectrig becomes: ** crankhome VR=ineffective ** camHALL input must be used, naturally http://www.vems.hu/files/ErikEnglund/pictures/IMG_0013.jpg If you need to check, basically same HW since v3.6 (eg. v3.8 or v3.8b), see "See also" below ---- '''For secondary trigger HALL''' (or sectrig unused) * either a small blob ("electric-short" or small resistor 1k or lower) is needed between the SOT23 NPN (base and collector) * or the NPN transistor is also perfect ** NPN inverts the signal, which is also good: sectrig edge is config-selectable falling/rising, just invert when moving config from ECU without camhall inverter to an ECU with camhall inverter. * and capture and verify Tools / triggerlog http://www.vems.hu/manual/html/images/Testing/v3.6_sec_trigger_1_m.jpg ---- * Does the HALL sensor have +5V supply ? * Is the camsync HALL signal connected to camHALL input ? (not the sectrig crankhome-VR input, which was made completely ineffective by the SJ7 solderblob=open '''When connecting, specify exactly ''' * connected how ? Exactly, which pins... mot55/ pin12, pin13 ? * measured what DC voltage ? ** measuring voltage on +5V and input pins, nothing on input ** measuring pin voltage, 1k pulldown between pin and GND ** +5V roughly remains +5V ** with strong internal pullup voltage drops from 4.5 ..5V to appr 1.35V ** with weak (18k) internal pullup voltage drops from 4.5 ..5V to appr 0.22V * triggerlog From AAN/21241 originally manufactured VR-auditrigger (not used before), removed the SJ7 solderblob but I get no response on either primary nor secondary trigger. (which pins are you trying ?) They tried to start it with '''VR 60-2 on pin 47''', no trigger pulses show up in VemsTune. * Saved config also needed so we can reproduce ** If still configured for c270 (135 tooth) auditrigger, maybe triggerlog wouldn't show up (needs missing tooth trigger for TriggerLog ) ---- '''See also:''' * GenBoard/VerThree/Schematic * InputTrigger/AudiTrigger * GenBoard/Manual/InputTriggerHardWare
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.