_   _ 
( ) ( )
| | | |
| | | |
| \_/ |
`\___/'
       
       

 _______ 
(  ____ \
| (    \/
| (_____ 
(_____  )
      ) |
/\____) |
\_______)
         

         
         
 #####   
 ##  ##  
 ##      
 ##      
 ##      
         

         
         
  ####   
 ##  ##  
 ##      
 ##  ##  
  ####   
         

  ____  
 / ___| 
 \___ \ 
  ___) |
 |____/ 
        

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
'''Setting up the serial port is very easy, since it's only 3 wires''' Still many people get it wrong first. Unfortunately the doc manual caused some confusion with swapped TX/RX. Check [http://www.aggsoft.com/rs232-pinout-cable/pinout-and-signal.htm rs232 pinout] yourself if you like. Note that DSUB25 (that is rarely used) standard has TX-RX swapped compared to DSUB9. (DSUB=DB). ---- === How to make the RS232 cable for GenBoard/VerThree === Only 3 wires are needed for the cable. Shielded cable is highly recommended in a production environment. Shield must be connected at only one side (either PC or GenBoard), so ground must have a dedicated wire inside the (min. 3 wires + shield) cable. ||'''DB9'''||Direction ||'''SV2'''||'''EC18'''||'''Earphone plug'''|| || || 3 ||--> ||1 ||EC18-pin14 ||RING ||Data transmitted by PC, received by genboard.|| || 2 ||<-- ||2 ||EC18-pin15 ||TOP ||Data received by PC, transmitted by genboard.|| || 5 ||<-> ||3 ||use GND ||Base ||You can use a GND pin (but NOT GND5: the power-GND would insert noise)|| SV2 is the 3 pin connector next to the MAX232 chip, near the regulator and EC18. Pin 1 on SV2 is the "top" pin, with GND on the side closest to the !EconoSeal loom connectors. Only the SV2 header is populated. The pinout of SV1 is the same. Pin 3 of SV1 is the pin closest to Pin 1 of SV2. The EC18-pin 14 and 15 are otherwise free pins that are often used (eg. fully assembled units shipped recently) for RS322. DB9 works well but using a 1/4" earphone plug looks cleaner in an automotive enviroment. Even if 3.5mm plugs is used in the Autronic harness their manual recommends using 1/4" plugs if it's installed in a panel. This is a good advice, go with the 1/4" plug. The biggest problem with 3.5mm is that most of the female connectors are low quality and will cause problems with time. [http://www.lammertbies.nl/comm/cable/RS-232.html RS232 Cable layouts] DB9 (==DSUB9) connector for PC/Genboard Communication: Please share the sources for above image. It counterrecmomends EC36-26 as GND for some unknown reason (EC36-pin26 is fine for this purpose). ---- '''How to use FBUS connection''' - TODO: detail useful with a device (or adapter cable) that doesn't have -+8V compatible RS232, just 0/3V serial connection (like PDA-s, mobile phones and their accessory-cables). Also good for bypassing the MAX232 for testing (eg. if MAX232 was killed by swapped RX-TX). For the PC=>AVR direction the trick is to '''tap onto the AVR-side of R52'''(=2k7, between the mcp3208 chip and LCD connector) to prevent conflict with the output of MAX232 (without unsoldering the MAX232). The '''AVR => PC direction is easy''', there should be no conflict with the MAX232's input (several inputs can listen on the same bus while only one can drive at a time). See UsbToFbus. ---- '''See also''' * GenBoard/Manual
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.