###      
 #####   
 ##  ##  
 ##  ##  
 ##  ##  
 ##  ##  
######   
         

  _      
 | |     
 | |     
 | |     
 | |____ 
 |______|
         
         

 _____ 
(_   _)
  | |  
  | |  
  | |  
  (_)  
       
       

  __  __ 
 |  \/  |
 | \  / |
 | |\/| |
 | |  | |
 |_|  |_|
         
         

   ____ 
  / ___|
 | |    
 | |___ 
  \____|
        

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Earlier, the in-firmware (mst.. msp.. commands) OutputTrigger was used to drive trigger signals. To test MembersPage/FiatStilo trigger code, we wrote new code (SVN firmware testing) to use PC soundcard as trigger signal generator. The code supports '''Primary trigger''' * multitooth ** m582: multitooth 60-2 ** m351: multitooth 36-1 * coiltype. eg. ** c040: coiltype with 4 cyl ** c080: coiltype with 8 cyl * fiat stilo ** f000: fiatstilo '''Secondary_trigger''' * default simple type (1 pulse /camrot) * fiat stilo cam (planned) '''TODO:''' make secondary trigger (edge positions) parametrizable from commandline Particuarly useful for GenBoard/Manual/InputTriggerCamSync. See [http://shop.x-dsl.hu/catalog/images/TestLightDumb_0002_s.jpg shop round testlight] item that is also very useful. '''Testing on the table can save hours or days of - sometimes frustrating - work'''. Small config or other errors can be very frustrating and difficult to find. If one knows that his config and ECM inputs and firmware are fine, she eliminated 70% of the problem-sources, and cut the number of possible problem-combinations to 1/10th. The '''cost is unfairly small, a few simple and cheap HW, and some work in the warm room'''. '''TODO:''' * '''document''' (easy usage) * release win binary ** porting should be simple, currently only uses very basic C libraries and outputs stereo 44100 sample/sec (like CD) wav file (on stdout) * integrate wit hfull duplex recording code, to record at the same time as outputting trigger ** useful to record some output (eg. ign output) ** should be easy on linux, as the record+play full duplex code is commited to same dir in SVN. But not yet integrated to the trigger generation code ---- '''Hardware''' - direct connection I simply connected the soundcard output to the ECM inputs, without any capacitor or resistor (the ECM has protection for the inputs anyway). * GND - GND (EC36pin26). The case of the jack connector. * left channel goes to primary trigger (EC36pin27). The tip of the jack male connector, if I'm right (TODO: check it) * right channel goes to secondary trigger ** EC36pin13 for secondary HALL ** EC18pin12 for secondary VR ("auditrigger") I listened via a headphone to both channels to tell crank from cam, before inserting the econoseal receptacles. With VR, there is no doubt it should work. With HALL input, maybe I was just lucky. The output level for the soundcard is 2V peak to peak, which is lower than the 0V/5V input that HALL is designed for. While it worked for me fine for first try, maybe I was lucky, and one needs to use 1..2 resistors to divide signal towards GND (1 resistor in the 10k range from input to GND should be enough to bias the input, the soundcard output is likely capacitively decoupled anyway). If in doubt, run mdf01mdkff menu-command, and in output watch for B.=.... benchstats. That should reveal if primary/secondary trigger pulses are detected with the right frequency. ---- '''See also''' * ElectronicDesign/SoundRecorder * ElectronicDesign
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.