##  ##  
  ####   
   ##    
  ####   
 ##  ##  
         

         
         
 ##   ## 
 ## # ## 
 ####### 
  #####  
  ## ##  
         

  ____  
 |  _ \ 
 | |_) |
 |  _ < 
 |_| \_\
        

   ##    
    #    
    #    
    #    
    #    
    #    
   ###   
         

 ______  
(  __  \ 
| (  \  )
| |   ) |
| |   | |
| |   ) |
| (__/  )
(______/ 
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
==== CommonRail - High pressure electronic diesel injection ==== ---- ---- :'''Technical papers:''' Modelling pressure waves in the rail http://www.vehicular.isy.liu.se/Publications/MSc/00_EX_3081_KA.pdf Paper on the effect of timing and duration of main and pilot injection. Mainly conserning noise levels. http://www.macchine.unisa.it/meca01/papers/MECA01_paper06.pdf Modelling of a diesel engine common rail injection system http://www.nt.ntnu.no/users/skoge/prost/proceedings/ifac2005/Fullpapers/04315.pdf Achieving lower exhaust emissions and better performance in an HSDI diesel engine with multiple injections http://www.tytlabs.co.jp/office/elibrary/ereview/rev373epdf/e373_009hotta.pdf Optimizing the multiple injection settings for a HSDI diesel engine http://books.google.com/books?id=-F7lKlRtKuIC&pg=PA123&hl=sv&source=gbs_toc_s&cad=1&sig=snbLjPZM0vEGKR5kGE_yAIhb7_s ---- :'''Issues:''' AFAIK there is no general aftermarket common rail diesel ECU available. This makes it impossible to use a common rail diesel in applications where the stock ECU does not work. One popular application can be marinisation of car engines. Another might be putting modern diesels in older cars. Or for tractors or gensets or whatever... One critical thing would be timing for injection ---- :'''Timing:''' A modern diesel does multiple injections each stroke. The pilot (and sometimes double-pilot) injectin is mainly for reducing noise at low revs. It also has a big effect on soot and NOx formation. At higher revs (>3000-4000) the pilot injection is not needed and only the main injection is needed. The post injection happens after the main injection, it also reduces emissions. I have not found any information on how it effects the torque or feul efficiency. Hence, at times we will have up to 3, or even 4, injections per stroke. These events will probably overlap between cylinders in some rev ranges on engines with more than say 5-6 cylinders. This may be difficult to implement. The hardware might also be limiting (recharging injector outputs etc). pilot injection ~ -40degrees (2-4mm^3) Timing not critical. Optimal timing is dependant on load and revs. Main injection no load -2 - 4 part load -6 - 4 full load -15 - -6 duration 40-60 deg crank 5000 crank rpm = 5000 / 60 rps = 5000/60 * 360 degps = 33us/deg average unexpected delay = 7us = 7/33 deg = 0.21deg We need data on injector properties (reaction time and dwell time as well as electrical properties.) We also need to know how critical the timing is. Is it the timing resolution or stroke-to-stroke repeatability that is important? ---- :'''Required I/O:''' ''''Glow plug output. A small typical diesel like Volvo D5244T4-7 uses max 12V and 22A during a minute. Most engines has a separate relay for this. Some engines regulate the voltage (and hence current) over the glow plug. The purpose is to reach high temperatures fast with a high current, after which the current is lowered to maintain the temperature. On larger (more plugs) or older engines it might not be feasable to output the required current directly from the ECU. It might then be better to control a relay. ''''Rail pressure sensor input Commonly outputs 0-5V. Needs +5V and an ADC ''''Rail pressure control valve output PWM regulated electromagnetic valve with coil resistance of 2-3Ohms. ''''Unit injector PWM regulated (pull and hold) up to 20A@80V for an typical electromagnetic injector. I don't have any data for piezolectric ones. ''''Commanded throttle position 0-5V or CAN ''''Manifold Air Pressure (MAP) ''''Manifold Air Temperature ''''Oil pressure ''''Coolant temperature ''''Crank shaft rotation sensor ''''Cam sensor ''''I/O for variable geometry turbo control ''''Other I/O for swirl throttle, output to pull starter selenoid. ----
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.