##    
         
  ###    
   ##    
   ##    
  ####   
         

  _  __
 | |/ /
 | ' / 
 | . \ 
 |_|\_\
       

 _       
( \      
| (      
| |      
| |      
| |      
| (____/\
(_______/
         

         
         
  ####   
 ##      
 ##      
 ##      
  ####   
         

         
         
 ######  
 #  ##   
   ##    
  ##  #  
 ######  
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
This is the list of components. There may be errors. You can help stocking by writing your estimated needs to the bottom. AfreshBoard BOM: ||'''Name'''||'''Value'''||.||'''Comment'''|| ||||||||Lambda circuit:|| ||R3||4.7k||1% hole||Max pump current 3mA.|| ||R6, R12||100k ||.||SMD 1206|| ||R9||100k||1% hole||.|| ||R13||20k ||1% hole||.|| ||R18||10k ||1% hole||.|| ||C12 ||100n ||.||RM2.5|| ||RHACK||4.7k||hole||Series resistor between OP and ADC, a trace need to be cut.|| Heater: T2 TIP121 TO220 Darlington NPN that that meet: 4A, 40W, 40V, hfe>=1k. xR1 1ohm 1% TO220 Caddock Coolpak MP930 30W TO220 resistor for heater current measurement. xC4 0.1u 1206 Input filter for heater driver f-3dB 16Hz R11 100k 5% 1206 Input filter for heater driver R34 20k 5% 1206 OP feedback R35 10k 5% 1206 Op feedback xR4 2.4k 5% 1206 Voltage divider for heater voltage measurement xR5 4.7k 5% 1206 Voltage divider for heater voltage measurement Power supply: IC4 L7805CV (ST) TO220 Most 7805 type regulators will work. Aim for at least 1A. (check LM2940T) DC1 Traco TMA0515D DC/DC converter +-15v, +-35mA. C1 1u RM5 0.33 and up C2 1u RM5 0 to 1u. C23,24,27,28 1u RM2.5 C29,30,31,32 1u RM2.5 D3 P2KE18A/P2KE20A Taiwan semiconductor. Transient suppression diode, also main component in the wrong polarity protection. D1 1N4004 Wrong polarity protection. At least 1A rating. D6 not used Can't figure out why I included it... IC4 L7805CV (ST) Minmum current rating 1A. F1 RC5 fuse Short circuit and wrong polarity protection. R61 200-2k 1206 Serial resistor for power led. D8 LED RM2.5 Power led Commo: C11, C15,C17,C18. 1u SMD 1206 If MAX232A or MAX202 is used the caps can be 0.1u. U$2 MAX232 SO16N MAX 232A and MAX202 can also be used. EGT: U$4 LM50 SOT23 Or LM45. 1 Euro. R21=R24 470k 1%! 1206 Must be matched! Patience will be awarded. R25=R28 470k 1%! 1206 Must be matched! Patience will be awarded. R22=R23 4.7k 1%! 1206 R26=R27 4.7k 1%! 1206 R21/R22=R25/R26 xR29,R31 Not used, gain adjustment. xR30,R32 1k pot hole Type 64, vertical. For offset adjustment xR10,R33 47k 1206 For offset adjustment. The offset adjustment can cause problems if the supply voltage are unbalanced, we will probably need to hack the offset adjustment a bit. LT1882 does not need offset adjustment. General: All OP's are LT1882. LM124/224/324 may work. I use 324 initially. (Jörgen) 7 Euro Atmel ATMega 128-16AI (16MHz, TQFP64) 18 Euro Microchip MCP3208CISL(external 8ch 12bit ADC) 5 Euro The HIP 9011 are available in many versions, we don't know which one we want yet. 8 Euro Jörgen * Use just initials, not email or postal addresses. The final order is via email. * Currently no full partkits, but R,C parts are easy to get at most places ----- PCB (15 Euro) - not in the set called every_chip ---- generated list: http://www.x-dsl.hu/genboard/AfreshBoard/ ---- Component number hints for groupbuy. This helps stocking: ---- MG: 3*every_chip, 5*PCB ---- JK: 3*every_chip, 6*PCB ---- MP: 1*every_chip + 1*PCB + 2*extra MAX232 + 5*MC34151P(1 Euro) + 1*L293NE(5Euro)? ---- MK: 1*every_chip + 2*PCB ---- DB: 1*every_chip + 2*PCB ---- DS: 1*every_chip + 2*PCB ---- MH: 2*every_chip + 2*PCB ------------------ These have been airmailed. Every_chip meant only atmega, max232 and LM324 soldered on. 40 Euro (or equivalent). The rest has not been ordered yet. Further orders via mail: cell at x-dsl.hu ----------- go back to AfreshBoard
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.